Copper wire
size (AWG)
Copper wire
size (AWG)
Length
of Cable
(Approx.)
CONNECTIONS
A. WV-CP230 (120V AC 60Hz)
Connect the power cord to an electrical outlet
of 120V AC 60Hz.
B. WV-CP232 (12V DC)
Connect the power cord to the DC 12V IN ter-
minal on the rear panel of the WV-CP232.
Resistance of copper wire [at 20°C (68°F)]
• Calculation of maximum cable length
between camera and power supply :
Resistance
Ω
/m
Resistance
Ω
/ft
#24
(0.22mm
2
)
0.078
0.026
#22
(0.33mm
2
)
0.050
0.017
#20
(0.52mm
2
)
0.03.
0.010
#18
(0.83mm
2
)
0.018
0.006
10.5V DC
≤
V
A
−
(R x 0.42 x L)
≤
16V DC
L : Cable length (meters)
R : Resistance of copper wire (
Ω
/meter)
V
A
: DC output voltage of power supply unit
V
A
−
12
L standard =
(meters)
0.42 x R
V
A
−
16
L minimum =
(meters)
0.42 x R
V
A
−
10.5
L maximum =
(meters)
0.42 x R
The following adjustment should be made by
qualified service personnel or system installers.
q
Loosen the screws on the flange-back adjust-
ing ring.
w
Turn the flange-back adjusting ring to the
desired position.
Caution:
When the C-mount lens is mounted,
do not rotate the ring counterclockwise
by force after it stops. If the ring is rotat-
ed by force, the inner lens or CCD image
sensor may be damaged.
e
Tighten the screws on the flange-back adjust-
ing ring.
FOCUS OR FLANGE-BACK ADJUSTMENT
12 V DC
(10.5 V - 16 V)
@
!
C. WV-CP234 (24V AC 60Hz)
Connect the power cable to the AC 24 V IN
terminal on the rear panel of the WV-CP234.
(m)
(ft)
#24
(0.22mm
2
)
95
314
#22
(0.33mm
2
)
150
495
#20
(0.52mm
2
)
255
842
#18
(0.83mm
2
)
425
1 403
Recommended wire gauge sizes for 24 V AC line
24 V AC, 60 Hz
(19.5 V - 28 V)
1
2
Installation of Auto Iris Lens
Connector
Install the lens connector (YFE4191J100) when
using a video drive ALC lens.
The installation should be made by qualified
service personnel or system installers.
Cut the iris control cable at the edge of the lens
connector to remove the existing lens connector
and then remove the outer cable cover of the sup-
plied connector as shown in the diagram.
The pin assignment of the lens connector is as fol-
lows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 1.3 V[p-p]/40 k
Ω
Pin 4: Shield, ground
Pin 3
Pin 4
Pin 2
Rib
Pin 1
Mounting the Lens
Caution:
Before you mount the lens, loosen the two
screws on the ring, and rotate this ring clock-
wise until it stops. If the ring is not at the end,
the inner glass or CCD image sensor may be
damaged.
q
Mount the lens by turning it clockwise on the
lens mount of the camera.
w
Connect the lens cable to the auto iris lens
connector on the side of the camera.
q
w
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount
(1”-32UN) and the lens weight should be less than
450
g
(0.99 lbs). If the lens is heavier, both the
lens and camera should be secured by using the
supporter.
The protrusion at the rear of the lens should be as
shown in the diagram.
C-mount: Less than 13 mm (1/2”)
CS-mount: Less than 8 mm (5/16”)
q e
w
Pick-up Device:
768 (H) x 494 (V) pixels, Interline Transfer CCD
Scanning Area:
4.92 (H) x 3.70 (V) mm (Equivalent to scanning area of 1/3”
pick-up tube)
Synchronization:
Internal, Line-locked or Multiplexed vertical drive (VD2),
selectable
Scanning System:
2 : 1 interlace
Scanning:
525 lines / 60 fields / 30 frames
Horizontal:
15.734 kHz
Vertical:
59.94 Hz
Horizontal Resolution:
480 lines
Video Output:
1.0 V[p-p] NTSC composite 75
Ω
/ BNC connector
Signal-to-Noise Ratio:
50 dB (AGC OFF, weight ON)
Electronic Light Control:
Equivalent to continuous variable shutter speed between 1/60 s
and 1/15 000 s
Minimum Illumination:
0.6 lx (0.06 foot-candle) at F0.75 [equivalent to 2.0 lx (0.2 foot-
candle) at F1.4] AGC ON
Detail:
SHARP or SOFT, selectable
Lens Mount:
C-mount or CS-mount, selectable
Ambient Operating Temperature:
−
10°C - +50°C (14°F - 122°F)
Ambient Operating Humidity:
Less than 90 %
Power Source and
WV-CP230:
120 V AC 60 Hz, 3.9 W
Power Consumption:
WV-CP232:
12 V DC, 270 mA
WV-CP234:
24 V AC 60 Hz, 3.7 W
Dimensions (without lens):
67 (W) x 65 (H) x 123 (D) mm
[2-5/8” (W) x 2-9/16” (H) x 4-13/16” (D)]
Weights (without lens):
WV-CP230:
0.62
kg
(1.37 lbs)
WV-CP232:
0.4
kg
(0.88 lbs)
WV-CP234:
0.43
kg
(0.95 lbs)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
SPECIFICATIONS
STANDARD ACCESSORIES
Body Cap............................................................................................1 pc.
ALC Lens Connector (YFE4191J100).................................................1 pc.
OPTIONAL ACCESSORIES
Lenses:
WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, WV-LA908C3,
WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LFY3C3,
WV-LFY45C3, WV-LFY9C3
Video Imaging Systems Company
A Division of Panasonic Broadcast & Television Systems Company
A Unit of Matsushita Electric Corporation of America
Executive Office: One Panasonic Way 4H-2, Secaucus, New Jersey 07094
Regional Offices:
Northeast:
One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Southeast:
1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838
Midwest:
1707 North Randall Road, Elgin, IL 60123 (847) 468-5211
Southwest:
8105 Beltsline Road, Suite 100, Irving, TX 75063 (927) 915-1334
Western:
6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
San Gabriel Industrial Park, 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00630 (809)750-4300
Solder the lens cable to the pins of the sup-
plied connector.
Flange-back
Adjusting Ring
Flange-back
Adjusting Ring
Screws
Screws
Caution:
To prevent fire or electric shock hazard, UL
listed wire VW-1, style 1007 should be used
for the DC 12 V or AC 24 V Input Terminal.
