manualshive.com logo in svg

Panasonic WV-X6511N, Operating Instructions Manual, Page: 62 / 265

Share
Download
Panasonic WV-X6511N Operating Instructions Manual Download Page 62

Note

•

Refer to [Frame rate*] in “2.3.2.8  Schedule: Set SD memory recording (video recording setup
menu)” for information about available frame rates and the bit rates that are set according to the frame
rate.

[Pre alarm (recording) duration]

Determine whether or not to perform the pre alarm recording. Set the duration to save image data on the SD
memory card.
Off/ 1s/ 2s/ 3s/ 4s/ 5s/ 8s/ 10s/ 15s/ 20s/ 25s/ 30s/ 40s/ 50s/ 60s

•

Default:

 Off

Note

•

The values change depending on the bit rate and the image capture size of the recorded stream. As
the selected bit rate increases, the available maximum value for the pre alarm duration decreases.

[Post alarm (recording) duration]

Set the duration to save image data on the SD memory card after an alarm occurrence.
10s/ 20s/ 30s/ 40s/ 50s/ 60s/ 120s/ 180s/ 240s/ 300s

•

Default:

 30s

* The actual recording time may sometimes be longer than the duration selected for this setting.

[Next] button

If you select “Alarm output” in the alarm setup menu and click the [Next] button, the alarm output setup menu
will be displayed. (

®

page 62)

If you click the [Next] button in the alarm setup menu without selecting “Alarm output”, the mail setup menu
will be displayed. (

®

page 63)

Note

•

If you click the [Next] button, the setting items in the screen are saved.

[Back] button

If you click the [Back] button, the alarm function type setup menu will be displayed. (

®

page 59)

2.3.2.5  Alarm: Configure the output terminal

Alarm output is configured in this section.

•

To configure settings relating to the output terminal:

Refer to page 151 for information about how to configure the above screen.

62

Operating Instructions

2 Settings

Summary of Contents for WV-X6511N










































































































































































































































































Reviews:

No comments