Camera
Sun Shade
Dummy cover
or IR LED unit
(optional)
Front glass
Wiper
PAN
rotation part
Mounting
pedestal
Tilt arm
Tilt lock
Side cover
Waterproof
EXT I/O
connector
Waterproof
RJ45
connector
Waterproof
power supply
connector
Bottom wiring port
Side wiring port*
1
Mounting pedestal
fixing screws ×4
(locally procured)
Dummy cover or IR LED unit
(optional)
IMPORTANT:
• When the camera is initialized, the settings including the network settings will be initialized. Note that the
CRT key (SSL encryption key) used for the HTTPS protocol and the preset entry will not be initialized.
• Before initializing the settings, it is recommended to write down the settings in advance.
• Do not turn off the power of the camera during the process of initialization. Otherwise, it may
fail to initialize and may cause malfunction.
STATUS indicator behaviors
• When the power is turned on
Lights orange
→
Lights off
→
Blinks orange
→
Lights orange (When the network connection is not established)
Lights orange
→
Lights off
→
Blinks orange
→
Blinks green
→
Lights green
(When the network connection is established)
• During the standby or connection
Lights orange (When the cable is not connected)
Lights green (When the cable is connected)
• During the upgrade process
Blinks orange
• During the initialization
Lights orange
→
Lights off
→
Blinks orange
→
Lights orange
• Port forwarding error caused by the UPnP function
Blinks orange (in 2 seconds intervals
(on for 1 second / off for 1 second))
• Trouble happening on the camera
Blinks red
• When the installation position is abnormal
Lights red
• This manual describes the installation procedures, network camera installation, cable connec-
tions, and adjustment.
• Before reading this manual, be sure to read the Important Information (included in the CD-ROM).
Parts and functions
Standard accessories
Cable preparation
Important safety instructions ......................... 1 pc.
Installation Guide (this document) ................. 1 set
Warranty card*
1
............................................ 1 set
CD-ROM*
2
.................................................... 1 pc.
Code label*
3
.................................................. 1 pc.
Attach the provided waterproof connector to the cable to be connected to the camera.
* When a conduit is used for wiring, always check its size before installing the waterproof connector.
Otherwise, the cable may not be able to pass through the conduit depending on the number of cables
used and the waterproof connector in use.
* Always make preparations before the procedure “[3] Attach the waterproof RJ45 connector (acces-
sory) to the Ethernet cable.”
* Prepare [1] and [2] when necessary.
*1 This product comes with several types of warranties. Each warranty is only applicable to the prod-
ucts purchased in the regions indicated on the relevant warranty.
*2 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*3 This label may be required for network management. The network administrator shall retain the code label.
Waterproof power supply connector (plug side) ...............................................................................1 set
Waterproof EXT I/O connector (plug side) ........................................................................................1 set
Waterproof RJ45 connector (plug side) ............................................................................................1 set
Washer nozzle mounting bracket A ..................................................................................................1 pc.
Washer nozzle mounting bracket B..................................................................................................1 pc.
Fixing screws for the washer nozzle mounting bracket B ..............................3 pcs. (of them, 1 for spare)
Attachment plate .............................................................................................................................1 pc.
Fixing screws for attachment plate ................................................................. 5 pc. (of them, 1 for spare)
Fixing nuts for attachment plate ..................................................................... 5 pc. (of them, 1 for spare)
Spring washer ............................................................................................... 5 pc. (of them, 1 for spare)
Flat washer .................................................................................................. 10 pc. (of them, 2 for spare)
Safety wire .......................................................................................................................................1 pc.
Wire clamper ...................................................................................................................................1 pc.
Bit (Hex wrench, screw size 6.35 mm {1/4 inches} T20)...................................................................1 pc.
Hub/Router
AC100-240 V
50/60 Hz
Ethernet cable (category 5e or better, straight)
Ethernet cable (category
5e or better, straight)
PC*
2
Tested PoE injector*
1
Installation procedure
• Attach the provided waterproof connector to the cable to be wired to the inside of the ceiling or
floor or along various surfaces, and run the cable through the conduit. (Please choose a conduit
of a suitable size to allow the connector to pass through.)
Cable preparation
• Remove the side cover of the camera so that the wire connection part is visible. (Step.4)
• If necessary, install the extension unit (IR LED unit) (optional) if necessary. (Step.5)
• If you want to shoot the foot area, bend the tilt arm of the camera forward. (Step.6)
• Fix the camera onto the installation location. (Step.8)
* Install the washer nozzle mounting bracket pre-fitted with a (recommended) washer nozzle at the
same time.
Installation
• Connect each waterproof connector to the camera, and fix the side cover back to its original position.
Connecting wires
(
→
Refer to the leaflet “Configuring
the camera so that it can be
accessed from a PC”)
• Turn on the power supply, and configure the camera so
that it can be accessed via network.
Configuring the camera so that it can be accessed from a PC
• About the INITIAL SW (Initial switch)
Follow the steps below to initialize the network camera.
➀
Cut the power supply to the camera either by unplugging the AC power cord or by turning off the
power supply of the tested PoE injector.
➁
Turn on the power of the camera while holding down the INITIAL SW, and keep the INITIAL SW held
down for 10-15 seconds. In about 2 minutes after releasing the INITIAL SW, the camera will start up
and the settings, including the network settings, will be initialized.
System connection diagram
The camera can be powered by the AC power supply or the tested PoE injector as shown in the follow-
ing illustration.
*1 For the related information on applicable tested PoE injectors, refer to our website
(http://security.panasonic.com/support/info/).
*2 Use an Ethernet cable (category 5e or better, cross) when directly connecting the camera to a PC.
*1 The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 or
ISO 228-1 (parallel pipe threads) G3/4.
[1] Attach the waterproof EXT I/O connector (accessory) to the cable
* The parts to be used in
➁
and
➂
are in the bag of the waterproof EXT I/O connector (plug side) set.
<Locally procured items>
• Multi-core cable
ø6.2 ~ 7 mm {ø1/4 ~ 9/32 inches}
Size of the internal lead wire
AWG26 – AWG30, coated external diameter of ø1 mm {ø1/32 inches} or below
• Manual crimping tool
HT-102/HR30-1, made by Hirose Electric Co., Ltd.
• Extraction tool (if necessary)
HR30-TP, made by Hirose Electric Co., Ltd.
➀
Thread each part of the waterproof EXT I/O connector (accessory) through the cable in
sequence
Pass the cord tube, cord clamp, gasket, spring and coupling in sequence through the plug beforehand.
Prepare wire ends according to the dimensions shown in the illustration below.
Case block
Coupling
Spring
Cord clamp
Gasket
Cord tube
Cable
15 ~ 20 mm {19/32 ~ 25/32 inches}
2.0 mm (+0, -0.5)
{3/32 (+0, -1/32) inches}
➁
Crimp the contact (accessory) to the cable
➂
Insert the contact into the terminal hole on the
case block
• After inserting the contact, pull the lead wire lightly,
and ensure that it is firmly fixed to the terminal hole
of the waterproof EXT I/O connector.
<Pin layout of the waterproof EXT I/O connector>
Pin. 1 LINE IN
Pin. 7
Alarm IN1
Pin. 2 Audio/LINE_GND
Pin. 8
N.C.
Pin. 3 Audio OUT
Pin. 9
Relay-
Pin. 4 Alarm GND
Pin. 10 Relay-
Pin. 5 Alarm IN3/AUX
Pin. 11 Relay+
Pin. 6 Alarm IN2/Alarm OUT
Pin. 12 Relay+
➃
Mount the coupling and the spring on the case block, and tighten the cord tube with the gasket
and the cord clamp
• Align the mark “
” on the coupling
with the side of pin
➀
of the case block,
and install the coupling and the spring in
sequence.
• Shift the cord tube, and insert the cord
clamp and the gasket in the cord tube.
• Align the cord tube with the coupling part,
and rotate to tighten them as shown in the
right illustration. (Recommended tightening
torque: 0.5 N·m {0.37 lbf·ft})
➄
Connect the washer unit (locally procured)
Pin. 9
Relay-
Pin. 10 Relay-
Pin. 11 Relay+
Pin. 12 Relay+
Waterproof EXT I/O
connector side
Circuit diagram
Washer unit connection
terminal side
Washer-
Nozzle
Washer hose
* Please use the washer unit that has been insulated from the commercial AC power.
➅
EXT I/O terminal ratings
• Alarm IN1, Alarm IN2, Alarm IN3
Input specification: No-voltage make contact input (4 V ~ 5 V DC, internally pulled up)
OFF: Open or 4 V ~ 5 V DC
ON: Make contact with GND (required drive current: 1 mA or more)
• Alarm OUT, AUX OUT
Output specification: Open collector output (maximum applied voltage: 20 V DC)
OPEN: 4 V ~ 5 V DC by internal pull-up
CLOSE: Output voltage 1 V DC or less (maximum drive current: 50 mA)
• Max. ratings of Relay+ and Relay-: DC 25 V, 4.0 A
* The default of EXT I/O terminals is “Off”.
[2] Attach the waterproof power supply connector (accessory) to the cable
* The parts to be used in
➀
and
➁
are in the bag of the waterproof power supply connector (plug side) set.
<Locally procured items>
• Power cable
Cable diameter
ø6 ~ 10 mm {ø1/4 ~ 13/32 inches}
Cross-sectional area of the wire conductor
0.75 or 1.25 mm
2
{0.0012 or 0.0019 inche
2
}
Number of wires
3 (for L, N and FG)
Insulation material
Polyethylene (recommended)
➀
Preparations
• Assemble the internal strain relief as shown in the right illustration,
and install the fixing bracket.
(Tighten the screws temporarily as the power cord will go in between
the bracket and the formed part.)
• Install the mounting gasket on the clamp
ring as shown in the right illustration. (Please
use the applicable parts as described below
for the mounting gasket according to the
external diameter of the power cord.)
Small internal diameter...
Power cord size 6.0 ~ 9.0 mm {1/4 ~ 11/32 inches}
Large internal diameter...
Power cord size 9.0 ~ 10.0 mm {11/32 ~ 13/32 inches}
➁
Thread each part of the waterproof power supply connector through the power cable in
the sequence as shown in the illustration below
• Cable nut
→
Clamp ring (with mounting gasket)
→
Back shell
→
Internal strain relief
Internal strain relief
Back shell
Clamp ring (with
mounting gasket)
Cable nut
Cable
➂
Prepare the cable end in the following dimensions, and twist the core.
Process tolerance: +1 mm/-0 mm {+1/32 / -0 inches}
Dimensions A (cable sheath) Dimensions B (bare core wire)
Live, Neutral 18 mm {23/32 inches}
7 mm {9/32 inches}
GND
20 mm {25/32 inches}
9 mm {11/32 inches}
➃
While the core of the lead wire is inserted into the connecting hole at the back of the
connector body, tighten the screw on the connector body, and connect
and fix the lead wire to each terminal.
For safety purpose, please read the following connection instructions carefully.
* There is a cutout on the connector coupling nut.
Align the position of the screw to be tightened with the cutout on the coupling
nut, and tighten the screw with a flathead screwdriver. (Refer to the upper
right illustration.)
(Recommended tightening torque: 0.5 N·m {0.37 lbf·ft}
During fore position
During upright position
Clamp ring
Mounting
gasket
Small internal
diameter
Large internal
diameter
Case block
Waterproof EXT I/O connector (accessory)
Terminal layout of the contact insertion side
Connector Pin
1 Live
Pin
2 Neutral
Pin
3 N.C.
GND
Cutout
Coupling nut
Pin 2
Pin 1
Pin 3
GND
➄
Insert and fix the internal strain relief on the connector as shown in the illustration. Next,
rotate the screw of the internal strain relief, and fix the power cord firmly with the fixing
bracket.
(Recommended tightening torque: 0.5 N·m {0.37 lbf·ft})
➅
Align the coupling nut to the fixing position to prevent
the connector from rotating, and rotate to fix the back
shell. Install the clamp ring (with mounting gasket) on
the back shell, and tighten it with a cable nut.
(Recommended tightening torque: 1.5 ~ 2.0 N·m {1.11 ~ 1.48 lbf·ft}
Coupling nut
Back shell
Cable nut
Clamp ring
(with mounting gasket)
Screws × 2
Internal strain relief
Internal strain
relief (accessory)
Fixing bracket
(accessory)
Screws x 2
(accessory)
Pin
➀
Coupling
Spring
Cord tube (Including the cord clamp and the gasket)
Case block
Installation Guide
Included Installation Instructions
Network Camera
Model No.
WV-SUD638
WV-SUD638-H / WV-SUD638-T
(Natural silver)
(Gray)
(Brown)
fles0816-1057 PGQX2063YA Printed in China
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic Corporation
Osaka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
© Panasonic Corporation 2017
Switch plate
STATUS indicator
ACT Indicator
LINK indicator
INITIAL SW
(Initial switch)
a
b
Connector body
2
4
3
5
7
6
8
56789
