85 mm {3-11/32 inches}
(85.7 mm {3-3/8 inches})
ø
25.4 mm
{
ø
1 inch}
*5
85 mm
{3-11/32 inches}
(85.7 mm
{3-3/8 inches})
138 mm
{5-7/16 inches}
ø
25.4 mm
{
ø
1 inch}
*5
138 mm
{5-7/16 inches}
83.5 mm
{3-9/32 inches}
46 mm
{1-13/16 inches}
ø
25.4 mm
{
ø
1 inch}
*5
63 mm
{2-15/32 inches}
ø
25.4 mm
{
ø
1 inch}
*5
63 mm
{2-15/32 inches}
83.5 mm
{3-9/32 inches}
ø
25.4 mm
{
ø
1 inch}
*5
108.5 mm
{4-9/32 inches}
70 mm
{2-3/4 inches}
ø
25.4 mm
{
ø
1 inch}
*5
Position A
Position D
Position B
Position C
Position E
Position F
Attachment plate (accessory)
Fixing screws for attachment plate: x4 (M4, locally procured)
Two-gang junction box
46 mm {1-13/16 inches}
83.5 mm {3-9/32 inches}
Installation
Step2 Fixing the brackets
Step1 Preparations
The installation tasks are explained using 4 steps.
There are 4 methods to install the camera to a ceiling or wall as described below. Prepare the
required parts for each installation method before starting the installation. The following are the
requirements for the various installation methods.
Installation method
Recommended
screw
Minimum pull-out
strength (per 1 pc.)
[1] Mount the camera on the two-gang junction
box using the attachment plate.
M4 screws x 4
196 N {44 lbf}
[2] Directly mount the camera onto the ceiling or
wall using the attachment plate (when wiring
can be installed in the ceiling or wall).
M4 screws x 4
196 N {44 lbf}
[3] Mount the camera onto the ceiling or wall using
the base bracket (when conduits are used for
wiring, or when there is no space available for
wiring in the ceiling or the wall).*
1
M4 screws x 4
196 N {44 lbf}
[4] Mount the camera embedded to a ceiling using
the WV-Q169A (ceiling mount bracket: approx.
705
g
{1.55 lb}).*
1
*
2
—
There is suf
fi
cient
strength in the ceiling
*1 Use 4 screws (M4 × 8 mm, accessory) to
fi
x the attachment plate to the base bracket or
WV-Q169A.
*2 For information on how to mount the camera embedded to a ceiling using WV-Q169A, refer
to the Instruction Manual provided with the WV-Q169A (ceiling mount bracket).
IMPORTANT:
Procure 4 screws (M4) to secure the attachment plate (accessory) or base bracket
●
(accessory) to a ceiling or a wall.
The minimum required pull-out capacity of a single screw or anchor bolt is 196 N
●
{44 lbf} or more when mounting with the installation method [1] to [3] above.
When mounting the camera on a concrete ceiling, use an AY plug bolt (M4) for
●
securing. (Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
Select screws according to the material of the ceiling
●
or wall that the camera will be
mounted to. In this case, wood screws and nails should not be used.
If a ceiling board such as plaster board is too weak to support the total weight, the
●
area shall be sufficiently reinforced.
[1] Using a two-gang junction box
[2] Directly mount the camera to the ceiling or wall using the attachment plate
[3] Mount the camera to a ceiling or a wall using base bracket
< When using the conduit on the ceiling
or wall for wiring>
The base bracket can be fixed in any of the following 6 screwing positions
according to ceiling and wall conditions. Match the hole used when
installing the camera to any of positions A to F.
<Mounting the base bracket>
q
Remove the cap for the female thread for
the conduit by using a hexagon wrench
(ISO 2936, width across flats S=5 mm
{3/16 inches}).
w
Mount the attachment plate and
the base bracket.
Attachment plate (accessory)
Fixing screws for attach-
ment plate: x4 (M4, locally
procured)
ø25.4 mm
*3
{1 inch}
ø73 mm
*4
{2-7/8 inches}
*5 The wiring hole diameter is 25.4 mm {1 inch}. Select any of the 2 base bracket fixture holes of
G
template B when installing the base bracket. After mounting the attachment plate, the mounting
direction of the camera can be adjusted in 90° increments.
*6 When attaching the base bracket to a one-gang junction box in Position E, secure the base bracket
with 2 screws (M4,
locally procured
).
IMPORTANT:
If open wiring is conducted, be sure to use conduits and run the cables inside
●
the tubes to protect the cables from direct sunlight.
Installation work shall be such that there is no exposure to water into the
●
architecture through the conduits having been joined.
Step1
Make sure all items are prepared
before beginning installation.
Step2
Mount the brackets to a ceiling or
wall
Step3
Connect cables, and then attach the
camera to the mount bracket.
Step4
Adjust the angle of view and focus,
and then mount the enclosure.
FRONT
Cap for the female
thread for the con-
duit
Base bracket (accessory)
Fixing screws (M4x4, locally
procured)
Minimum pull-out
strength: 196 N {44.06 lbf}
(per 1 pc.)
Fixing screws for attachment
plate: x4 (accessory)
(Recommended tightening
torque: 0.78 N·m {0.58 lbf·ft})
Attachment plate
(accessory)
*3
If the mounting direction of the camera has already been determined
Align the FRONT direction (the direction of FRONT marker on the camera that indicates the
installation direction when installing the camera) of
F
template A with the desired direction, and
drill through a 25.4 mm {1 inch} diameter hole.
*4
If the mounting direction of the camera is not determined yet or if you want to change
the direction of the camera after it has been installed
If you want to be able to change the direction of the camera, drill through a 73 mm {2-7/8 inches}
diameter hole in the center. By doing so you can adjust the mounting direction of the camera in
90° increments.
Step3 Mount the camera to the attachment plate
Step4 Adjustment
q
Check the position of attachment
mounting screws on the rear side
of the camera.
w
Connect cables to the camera according to
the instructions in “Making connections”, and
mount the camera by inserting the attachment
mounting screws into the holes of the attach-
ment plates.
e
Loosen the enclosure
fi
xing screws.
r
Remove the enclosure from the camera,
and secure the camera using camera
fi
xing screws.
Note:
After cables have been connected to the camera, align the OPEN mark of the enclosure
●
side panel with the protruding part of base bracket, insert 2 attachment mounting screws
into the attachment plate, and rotate the camera approximately 15°. The LOCK mark is
moved to the protruding part of base bracket and the camera is temporarily secured.
(When directly attaching the attachment plate to a ceiling or wall, align the OPEN mark to
the tab position of the attachment plate.)
*The fixing angle of the camera can be rotated in 90° increments
.
Note:
Loosen 4 enclosure fixing screws
●
using the bit (accessory).
IMPORTANT:
Be sure to tighten the camera fixing
●
screw. Failure to observe this may
cause camera trouble due to camera
falling. (Recommended tightening
torque: 0.78 N·m {0.58 lbf·ft})
q
Turn on power for the camera by either
connecting a LAN cable or a 12 V DC
power cable, and then remove the protec-
tion
fi
lm from the camera lens.
w
Connect the MONITOR OUT conversion
plug (accessory) to the MONITOR OUT
terminal of the camera, and then connect
the monitor for adjustment with a RCA pin
cable (locally procured).
The camera is set to be connected to the
●
NTSC monitor for adjustment at factory
shipment.
To remove the SD memory card, hold down the SD ON/OFF
●
button for about 2 seconds. When the flashing SD MOUNT
indicator goes out, you can remove the SD memory card.
After the SD memory card has been replaced, press the
●
SD ON/OFF button, and make sure the SD MOUNT
indicator is continually lit. (If you replace both SD memory
cards, press the SD ON/OFF button after replacing the
cards.)
If you do not press the SD ON/OFF button after replacing
●
the SD memory card, the SD MOUNT indicator is
continually lit approximately 5 minutes later.
When adjusting the viewing angle, make sure not to touch
●
the light-blocking rubber ring or IR LED cover. Fingerprints
or dirt can reduce the quality of viewed images.
IMPORTANT:
After adjusting the angle of view, tighten the cross
●
slot tilting lock screw.
(Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
e
Adjust the angle of the camera with the
tilt table, pan table, and azimuth adjust-
ment ring, and then adjust the viewing
angle by pressing the WIDE or TELE
buttons, and tighten the cross slot tilting
lock screw
fi
nally.
Horizontal position (Panning):
±
180°
Vertical position (Tilting): 0° to 85°
Image tilt adjustment:
-45°(Left) to +300°(Right)
r
Insert an SD memory card into the slot,
if necessary.
t
Disconnect the monitor for adjustment
after adjusting the focus by pressing the
AF button.
y
Attach the enclosure.
(Align the
mark on the camera body
with the LOCK line on the enclosure
and then mount the enclosure to the
camera body at a straight angle.)
E
MONITOR OUT conversion plug
(accessory)
Note:
When the screen size is adjusted using the WIDE
●
button or TELE button, the camera’s focus is
automatically adjusted with the basic focus adjustment function each time the WIDE button or
TELE button is pressed.
Depending on the vertical position (tilting) range or the optical zoom, it must be noted that the
●
shadow of the enclosure may be projected.
When adjusting the viewing angle for cameras mounted to ceilings, the enclosure and installation
●
auxiliary wire may be displayed on the screen depending on the direction the camera is facing.
Move the enclosure and installation auxiliary wire so that they are not displayed on the screen.
When mounting the camera on a ceiling, adjust the tilt angle so that the TOP mark above the lens
●
always comes to the top side.
When the camera is installed to a wall, the image is reversed in the default settings. To correct the
●
way the image is displayed, rotate the azimuth adjustment ring 180° clockwise, or select “On” for
“Upside-down” from the setup menu. For information about performing the “Upside-down” setting
from the setup menu, refer to the Operating Instructions (included in the CD-ROM).
Remove the camera using the reverse order of the installation procedures.
●
IMPORTANT:
Securely tighten all the fixing screws (x4) of enclosure. Otherwise, camera dropping may
●
result in injury. (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
Defocus may be caused by the reinstalled enclosure. In this case, perform the auto focus
●
function from the setup menu.
Remove the cover film from the dome cover.
●
Approx. 15°
Enclosure
Camera fixing screw
Attachment mounting screws
IMPORTANT:
Disconnect the 12 V DC power source and PoE power source to prevent power from being
●
supplied during mounting work.
Enclosure is fixed at the installation auxiliary wire to the camera body, please do not
●
remove the installed auxiliary wire.
For installations on the wall, to prevent water from accumulating on the surface of the
●
dehumidifying device, install the camera so that the dehumidifying device does not face up.
If water accumulates on the surface of the dehumidifying device, it cannot function properly.
< When drilling a hole through the
ceiling or wall for wiring>
The female thread for conduit is compliant
●
with ANSI NPSM (parallel pipe threads) 3/4
or ISO 228-1 (parallel pipe threads) G3/4.
*
6
After installing the camera, refer to “Configure the settings of the camera (leaflet)” and
perform the camera settings.
Tab position
of the attach-
ment plate
(x4)
Conduit
Protruding part (x4)
Insert the SD memory card with its label
●
facing down.
Refer to the Operating Instructions on the
●
provided CD-ROM for further information
about the SD memory card settings.
46 mm
{1-13/16 inches}
83.5 mm
{3-9/32 inches}
NTSC
PAL switch
WIDE button
AF button
SD1, SD2
TELE button
Direction marker
for installation
(FRONT )
Tilting lock screw
Installation auxiliary
wire
The enclosure is
rotated and the
camera is tem-
porarily secured.
