Panasonic WV-SFN310A Operating Instructions Manual Download Page 113

Page: 113 / 222

[Audio output port (PC to Camera)]

SFx311

SPN311

SPW311L

SPN531

SPW531L

Enter the transmission port number (the port number on the camera used to receive audio data transmitted
from the PC).

•

Available port number:

1024-50000 (Only even numbers are available.)

•

Default:

34004

Note

•

The transmission port number entered for “Audio output port (PC to Camera)” will be used only when
“Unicast port (MANUAL)” is selected for “Transmission type” (

page 79).

When “Off” is selected for “H.264 transmission” (

page 79) or when “Unicast port (AUTO)” or

“Multicast” is selected for “Transmission type”, it is not necessary to enter the transmission port number.

[Permission level of audio trans./recep.]

SFx311

SPN311

SPW311L

SPN531

SPW531L

SFN310

SPN310

Select an access level for audio transmission/reception from the following.
1. Level 1 only/ 2. Level 2 or higher/ 3. All users

•

Default:

3. All users

Note

•

Refer to page 140 for further information about the access level.

Operating Instructions

113

11 Configure the settings relating to images and audio [Image/Audio]

Summary of Contents for WV-SFN310A































































































































































































































Search results

Summary of Contents for WV-SFN310A

Reviews:

Brands by name

Popular brands

Panasonic WV-SFN310A, Operating Instructions Manual

Search results

Summary of Contents for WV-SFN310A

Reviews:

Brands by name

Popular brands