background image

3

Preface

This mount bracket is used for installing the color CCTV camera or network camera on a wall.
Refer to the catalog or operating instructions of the camera for further information about the compatible models.

Precautions

Refer installation work to the dealer.

Installation work requires technique and experiences.
Failure to observe this may cause fire, electric shock, injury, 
or damage to the product.
Be sure to consult the dealer.

Avoid installing this bracket in the locations where 
corrosive gas is produced.

Otherwise, the mounting portions will deteriorate and acci-
dents such as a fall of this product may occur.

The screws and bolts must be tightened to the speci-
fied torque.

Loosening of mounting screws or bolts may cause a fall of 
the product resulting in injury or accidents.

Do not use this bracket except with suitable cameras

Failure to observe this may cause a drop resulting in injury.

Select an installation area that can support the total 
weight.

Selecting an inappropriate installation surface may cause 
this product to fall down or topple over, resulting in injury or 
accidents.
Installation work shall be started after sufficient reinforce-
ment.

Do not rub the edges of metal parts with your hand.

Strong rubbing may cause injury.

Periodic inspections shall be conducted.

Rust on the metal parts or screws may cause a fall of the 
product resulting in injury or accidents.
Consult the dealer for the inspections.

The measures of protection against a fall of this prod-
uct shall be taken.

Failure to observe this may cause a drop resulting in injury.
Be sure to install the safety wire.

Do not install this product in locations subject to 
vibration.

Loosening of mounting screws or bolts may cause a fall of 
the product resulting in injury or accidents.

Install this product in a location high enough to avoid 
people and objects from bumping the product.

Failure to observe this may cause injury.

Do not hang down from this product or use this prod-
uct as a pedestal.

Failure to observe this may cause injury or accidents.

Do not install the product in a windy place.

Installation of the product in wind with a speed of 60 m/s or 
more may cause a drop resulting in accidents.

The measures of protection against snowfall shall be 
taken.

Weight of snow may cause a fall of the product resulting in 
injury or accidents.
Protect the product against snowfall by installing under 
eaves.

Summary of Contents for WV-Q122AS

















Reviews: