background image

Model No.

Installation Guide

Model Name

Model No.

Wireless Video Intercom System

VL-SWD273

Video Intercom System

VL-SVD273

Main Monitor Station

VL-MWD273

R

This guide is for use with the above 3 models.

VL-V554

VL-MWD273

Door station

Main monitor station

R

The Installation Guide in Indonesian can be accessed from the following site:
https://panasonic.net/cns/pcc/support/intercom/swd273

R

Door station is described as "doorphone" and Main monitor station is described as "main
monitor" in this guide.

R

In this guide, the suffix of each model number (e.g., the "BX"  in "VL-MWD273BX") is omitted
unless necessary.

Note to the installer

R

Before attempting to connect or operate this product, please read the label on the rear of
the doorphone and the main monitor/extension monitor.

R

Please read this guide carefully, and install the product safely and correctly by following
the instructions. Carefully read the information found in the section titled "For your
safety" in particular.

R

Only use attachments/accessories specified by the manufacturer.

R

The installation shall be carried out in accordance with all applicable installation rules.

R

R

After installation, make sure to leave this guide with the customer.

To the maximum extent permitted by law, Panasonic assumes no responsibility for 
injuries or property damage resulting from failures arising out of improper installation or 
operation inconsistent with this document.

273_ig.book  Page 1  Friday, April 28, 2017  9:46 AM

Summary of Contents for VL-SWD273

















Reviews: