background image

2

Important Information

Introduction and Installation

Included items ............................................................................................................ 5
Location of controls ................................................................................................... 6
Before installation ...................................................................................................... 7
Installing the door station .......................................................................................... 8

Help

Cleaning ................................................................................................................... 12

General Information

Technical data about this product ............................................................................ 13

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause

undesired operation.

FCC and Other Information

CAUTION:

Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.

Important Information

FCC and Other Information ....................................................................................... 2
Important safety instructions ..................................................................................... 3
Additional safety information ..................................................................................... 4
For best performance ................................................................................................ 4

Summary of Contents for VL-GC002A

















Reviews: