Panasonic VB-44210G User Manual Download | Manualshive

Page: 65 / 394

background image

Section 700 - Operation

Chapter 3. System Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page 3-19

same DNIS number and both ports do not answer a delayed ringing call, the
call follows the call forwarding settings of port 125.

DID/DNIS Text Name Assignment

(CPC-B Version 5.0 or higher)

Description

DID/DNIS Text Name Assignment allows the assignment of text names to
specific DID/DNIS numbers. The text name can include up to six characters.

Text name assignments are especially useful when multiple DID or DNIS
lines terminate to the same extension or group. For example, a call center may
handle inquiries for three different companies. To easily identify which
customer is being called, individual DID or DNIS numbers can be assigned
for each customer, and then corresponding text names can be assigned to the
DID or DNIS trunks.

Up to 200 DID text names and 200 DNIS text names can be assigned.

Related Programming

• FF1 (System): Inbound DID Dial Numbers

• FF1 (System): DNIS Number Setting

Considerations

• A DSS/72 is required to assign text names to DID/DNIS trunks.

• If text is assigned to a DID/DNIS number that rings at multiple extensions,

all of the extensions will receive the text display.

• The text display follows forwarded calls and transferred calls.

• If text is not assigned to a DID/DNIS line, the number will display.

«
...
63
64
65
66
67
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Jabra Pages: 2

FUSION Apollo MS-WB670

Brand: Garmin Pages: 44

Bell & Gossett ecocirc XL Series

Brand: Xylem Pages: 62

Brand: Uniden Pages: 41

Brand: BT Pages: 12

myPhone Jazz 202112

Brand: mPTech Pages: 65

Brand: GE Pages: 100

Brand: Kirstein Pages: 4

Brand: Magnavox Pages: 12

Brand: Elenberg Pages: 36

Brand: Panasonic Pages: 32

VB44210A - BUSINESS TELEPHONE

Brand: Panasonic Pages: 50

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands