Panasonic VB-44210G User Manual Download Page 366 | Manualshive

Page: 366 / 394

background image

Appendix I. CPC-EX 2.3 Feature Update

Section 700-Operation

Page I-2

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

and remote passwords. The private password may always be used to enter the
system.

*Additional Remote Administration Interface (RAI) Access Method

- In

addition to the existing RAI access, a new RAI access method has been
added. The RAI access allows an incoming call to be transferred to the RAI
(either manually or by Automated Attendant) and then the caller enters the
remote or private password.

ISDN Programming Flexibility

- The existing ISDN programming has been

enhanced to allow programming flexibility in the following areas: Network
Type, Auto Progress, NSF, ISDN CO Type, ISDN International Dial Code
Deduction, ISDN Long Distance Code 1 Deduction, and ISDN Type and Plan
Option.

Software Corrections

SMDR Stopped Printing

- In earlier versions, the SMDR output from the

DBS would stop printing and not reset. This problem has been corrected with
this version.

SMDR Header Printed More Often Than Every 60 Lines

- In earlier

versions, the SMDR header printed more than every 60 lines. In this version,
the SMDR header now correctly prints out every 60 lines.

Last Digit of Voice Mail One Touch Key Was Truncated

- In earlier

versions, if a Voice Mail One-Touch Access key was programmed when the
key was viewed with the Conf. Function, the last digit of the programmed
information could not be seen.

Previously Unable to restrict 800+ Numbers for TRS types 5 and 6

- In

the previous version if an 800-xxx number was entered in the special area and
special office code tables with the new North American Numbering Plan
(NANP) activated TRS types 5 and 6, it did not restrict the call. This problem
has been corrected in this version.

Override Toll Restriction with SSD Numbers Address Was Not Available

- In the previous version, the programming address FF1 2#1#4# could not be
accessed. The address is now available in this version.

DID Call to a Voice Mailbox Received Main Greeting

- In the previous

version, in a Non-Integrated Digital PanaVOICE environment, if a DID/
DNIS call was directed directly to a voice mail box, the caller was sent to the
main greeting instead of the correct voice mail box. This problem has been
corrected with this version.

Unusual First Ring on Incoming ISDN Calls

- Previously incoming calls

on ISDN line had a long ringing pattern (6 seconds ON or more, then OFF).

«
...
364
365
366
367
368
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Valcom Pages: 1

Brand: Valcom Pages: 13

Yealink SIP-T22P

Brand: Yealink Pages: 2

Brand: Yealink Pages: 3

digital slim -1400

Brand: Fisher Pages: 20

Brand: Main Resource Pages: 5

Brand: GE Pages: 97

Brand: Haken Audio Pages: 7

Brand: SoftBank Pages: 307

Brand: DMGT Pages: 3

Brand: Aastra Pages: 9

Brand: Waterboy Pages: 2

Brand: Water Care Pages: 20

Brand: base engineering Pages: 26

Brand: Looperlative Pages: 29

Brand: Power Dynamics Pages: 16

Brand: Aristel Pages: 50

Brand: Olive Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands