Panasonic VB-44210G User Manual Download | Manualshive

Page: 306 / 394

background image

Appendix A. EX 1.0 Feature Update

Section 700-Operation

Page A-16

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Barge-Ins During Handset Mute.

If another phone barges in on your call

while Handset Mute is ON, and you change to conference talk (but not by
pressing HOLD), Handset Mute will remain ON.

FF-Key/One-Touch Key Restriction.

Handset Mute cannot be assigned to

an FF-key or a one-touch (soft) key.

Off-Hook Monitoring

Description

Off-Hook Monitoring lets you put a call on speaker while the handset is
off-hook. You can still communicate with the outside party via the handset,
but you will also be able to hear the other party on the phone’s speaker. He/
she will only be able to hear what is spoken through your handset, however
- audio will not be transmitted through your microphone.

Operation

1.

During a call, press the ON/OFF key.

• Another receiver path is established on the phone’s speaker

-- you can now hear the outside party on the speaker as well
as in the handset.

• Your phone’s microphone is muted so that the outside party

hears only what is spoken through your handset. (To mute
handset transmission, press MUTE.)

2.

To turn off Off-Hook Monitor (“kill” the speaker but stay on
the line with the outside party through the handset), press ON/
OFF again.

Analog Adapter

Description

The Analog Adapter (VB-44100) consists of a base adapter and PC board
which is installed on the underside of the phone. It is used to connect the
44-Series large-display phone to an analog device such as an SLT
telephone, cordless phone, FAX machine, or modem. This allows the same
phone line to be used to alternate between normal phone calls and analog
communications.

(To install, see the instructions supplied with VB-44100).

Programming

See

Section 400 - Programming (Appendix C)

for more detailed

programming information.

Operation

«
...
304
305
306
307
308
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Panasonic Pages: 8

Wireless Service Gateway WSG

Brand: Unify Pages: 39

Brand: Centrios Pages: 13

Brand: Uniden Pages: 16

Brand: Uniden Pages: 36

Brand: AT&T Pages: 36

Brand: Bang & Olufsen Pages: 44

Brand: Serene Pages: 30

AERCO AquaSolve AM8408-COM

Brand: Watts Pages: 8

Brand: Water Control Pages: 20

Brand: SoundRyder Audio Pages: 20

Brand: AdvanceTec Pages: 8

Brand: JVC Pages: 29

Brand: JVC Pages: 28

Brand: JVC Pages: 36

Brand: JVC Pages: 20

Brand: JVC Pages: 2

Brand: JVC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands