Panasonic VB-44210G User Manual Download | Manualshive

Page: 275 / 394

background image

Section 700 - Operation

Chapter 6. SLT Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

6-19

Camp-on

(CPC-A 3.1 or higher, CPC-AII, and all Versions of CPC-B)

Description

If you reach a busy extension, you can use the Camp-on feature to alert you
with a ring when the extension becomes free. You can then pick up your
handset to automatically dial the extension.

Operation

To activate the Camp-on feature:

1. Lift the handset.

2. Dial the desired extension number.

3. Upon hearing busy tone, press “3.”

• The phone issues ringback tone.

• If the Camp-on feature is not available, the phone continues to issue a

busy tone.

4. Replace the handset after you hear the ringback tone.

5. Wait for the callback ring.

To answer the callback ring:

Pick up the handset when you hear the callback ring.

The system automatically dials the called extension.

Related Programming

• FF3 (Extension): Call Waiting/OHVA Tone

• FF3 (Extension

Considerations

• The callback ring must be answered within sixteen seconds or it is

canceled.

«
...
273
274
275
276
277
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: NEC Pages: 42

Brand: NEC Pages: 8

Brand: NEC Pages: 220

Brand: NEC Pages: 2

PhoneEasy Display 312C

Brand: Doro Pages: 20

Feeder/Deliming System EV9797-20

Brand: Everpure Pages: 2

Brand: Sennheiser Pages: 2

Brand: GE Pages: 28

Brand: Telstra Pages: 40

Brand: VocoPro Pages: 26

Sportsound SSR-300

Brand: Daktronics Pages: 6

Brand: Binatone Pages: 36

Brand: VTech Pages: 46

Brand: GE Pages: 38

LINKBRIDGE LBO-DP12-R-2F

Brand: Broadata Communications Pages: 14

Brand: iWantit Pages: 32

Gigaset M2 plus professional

Brand: Unify Pages: 61

Brand: Geemarc Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands