background image

Chapter 6. SLT Features

Section 700 - Operation

 

6-6

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Considerations

• You cannot break in on three-party conference calls.

• The default for the override alert tone is “off.” If the override alert tone is 

enabled, the tone will be sent to both parties when a call is overridden.

Call Forwarding

(All Versions) 

Call Forwarding allows users to send their calls to another extension, to an 
outside line, or to voice mail. All versions of the DBS provide call 
forwarding; however, some call forwarding enhancements are not available 
with earlier versions. The following table shows the call forwarding features 
available with each release. 

Table 6-3.  DBS Call Forwarding features

Call Forwarding--All Calls

. When this feature is activated, all incoming 

calls to an extension are forwarded immediately.

Call Forwarding--No Answer.

 When this feature is activated, an 

unanswered call rings until the Call Forward No Answer timer expires. When 
the timer expires, the unanswered call is forwarded.

Feature

Availability

Call Forwarding--All Calls

All versions

Call Forwarding--No Answer

CPC-AII and CPC-B Version 2.0 
or higher

Call Forwarding--Busy

All versions

Call Forwarding--Busy/No Answer

All versions

Call Forwarding--External

CPC-A, CPC-AII prior to 7.0 and 
CPC-B prior to 7.0. Beginning 
with CPC-AII and CPC-B Ver-
sion 7.0, all forwarding types (All 
Calls, No Answer, Busy, Busy/
No Answer) allow call forward-
ing outside -- eliminating the 
need for Call Forwarding--Exter-
nal.

Permanent Call Forwarding

CPC-AII and CPC-B Version 3.1 
or higher

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews: