Panasonic VB-44210G User Manual Download Page 225 | Manualshive

Page: 225 / 394

background image

Section 700 - Operation

Chapter 5. DSLT Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

5-7

2. Dial the extension number.

3. When you hear busy tone, dial “4.”

• Both phones issue an alert tone (system programming required).

Related Programming

• FF1 (System): Alert Tone for Busy Override and OHVA

• FF1 (System): Extension Class of Service Setting (CPC-AII and CPC-B

Version 3.1 or higher)

• FF3 (Extension): Extension Class of Service Assignment (CPC-AII and

CPC-B Version 3.1 or higher)

• FF3 (Extension): Busy Override Send

• FF3 (Extension): Busy Override Receive

• FF3 (Extension): Extension Page Group

Considerations

• You cannot break in on three-party conference calls.

• The default for the override alert tone is “off.” If the override alert tone is

enabled, the tone is sent to both parties when a call is overridden.

Call Forwarding

(All Versions)

Description

Call Forwarding allows users to send their calls to another extension, to an
outside line, or to voice mail. Some call forwarding enhancements are not
available with earlier versions of the DBS. The following table shows the call
forwarding features available with each version.

Table 5-3. DBS Call Forwarding features

Feature

Availability

Call Forwarding--All Calls

All versions

Call Forwarding--No Answer

CPC-AII and CPC-B Version 2.0 or higher

Call Forwarding--Busy

All versions

«
...
223
224
225
226
227
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: DAB Pages: 8

Brand: Yealink Pages: 2

GreenSpec HTHB-HVRGRN

Brand: Halsey Taylor Pages: 7

ETIQUETTE MEMOIRE M I740N

Brand: Aastra Pages: 1

Brand: Daewoo Pages: 48

Brand: Grundig Pages: 16

Brand: Uniden Pages: 89

Brand: Icom Pages: 50

Brand: SAL Pages: 20

Brand: VTech Pages: 56

Brand: ImageTech Pages: 2

Brand: MAJORITY Pages: 26

Brand: Bosch Pages: 40

Brand: Bosch Pages: 21

Brand: Bosch Pages: 498

Brand: Hitachi Pages: 44

Brand: Sharp Pages: 116

Brand: Sanyo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands