Panasonic VB-44210G User Manual Download Page 224 | Manualshive

Page: 224 / 394

background image

Chapter 5. DSLT Features

Section 700 - Operation

5-6

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Forwarding. In versions prior to 5.0, incoming trunk calls to extensions are
routed according to the ringing assignment for the trunk.

The following types of incoming trunk calls follow Permanent Call
Forward settings:

- Direct trunk calls (including DID/DNIS)

- Transferred trunk calls.

Auto Redial

(CPC-AII and CPC-B Version 7.0 or higher)

Description

If the Redial key is pressed when the extension is idle or receiving dial tone,
the last intercom or outside number is automatically redialed.

Related Programming

• FF3 (System): Auto-Redial on Extensions

• FF1 (System): Extension Class of Service Setting

• FF3 (Extension): Extension Class of Service Assignment

Busy Override

(All Versions)

Description

Extensions in the same Paging Group (1-7) can break into one another’s
outside or intercom calls to relay information or to create three-party
Conference Calls.

Operation

1. Pick up the handset.

The phone issues intercom dial tone.

«
...
222
223
224
225
226
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Samsung Pages: 79

Brand: Samsung Pages: 88

Brand: Samsung Pages: 215

Brand: Samsung Pages: 155

Brand: Ace Pages: 13

FUSION Apollo MS-WB670

Brand: Garmin Pages: 44

Brand: Pacific Sun Pages: 12

Brand: Hama Pages: 75

Wave SoundTouch IV series

Brand: Bose Pages: 32

Brand: Innovative Technology Pages: 14

Brand: Biamp Pages: 6

Brand: GE Pages: 60

Brand: Clarity Pages: 2

XDECT 8005WP Series

Brand: Uniden Pages: 12

Brand: VanAccess Pages: 24

Brand: Rockville Pages: 10

Brand: switel Pages: 120

Brand: Alto Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands