102
Message
Meaning / Action
All contents will be lost.
Are you sure to delete this device?
Once you unregister the USB HDD, all the recorded programme will be
●
erased.
All tuning data will be erased
“Shipping Condition” will erase all tuning data (p. 51).
●
Are you sure ?
Confirm correct operation.
●
Are you sure you want to delete this timer ?
Press OK to delete timer.
Press RETURN to return.
Confirm correct operation.
●
Bad signal
The signal is weak. Check the aerial is plugged in properly. It may be
●
necessary to have an aerial installer check the signal and aerial alignment.
Reset channels. (p. 40 and p. 41)
●
Cannot register another device because
the list is full.
Up to 8 USB HDDs can be registered with this TV.
●
Child Lock is active!
Press OK to enter PIN.
The selected channel is locked in Child Lock (p. 54). You must enter the
●
PIN number before the channel will be displayed.
Faulty dish
The satellite cable might be short-circuited or there might be connection
●
problems of the cable. Check the cable and connection and then turn the
TV Off with the Mains power On / Off switch, and turn it On again.
If the message still persists, it may be necessary to have a dish installer
●
check the dish and cable.
Feature not available.
It is not possible to record from COMPONENT or HDMI. Connect the
●
recorder to the TV using a fully wired SCART cable for recording from the
TV tuner.
Confirm Q-Link or VIERA Link settings (p. 84 - 87).
●
Feature not available.
Press OK to view how it works.
The selected feature on VIERA TOOLS is not available. Press the OK
●
button to view the demonstration to explain how to use it.
Found new software version
∗∗∗
.
Press OK to start update (may take
40 mins) or Press EXIT to ignore
and you can update when TV is in standby
There is a new software available.
●
Invalid operation - Please check settings
and connections.
Check the Q-Link or VIERA Link connection and setting (p. 84 - 87).
●
Invalid system time. Please exit !
Cannot get the time information and cannot edit Timer Programming
●
screen. Check the connection of the RF cable.
Invalid system time, Timer Programming
will not work.
Please press TV button on remote control
and check time display on Banner
Cannot get the time information. If there is no time displayed on the
●
Information banner, check the connection of the RF cable.
Max. number of timers already set !
The maximum number of timer programming events is 15.
●
New channels found!
Press OK to update channel list.
Press EXIT to ignore.
There may be new channels available.
●
This message will appear each time a change is made by the
●
broadcasters. This message can be deactivated by setting “New Channel
Message” to Off in “DVB Tuning Menu”.
Selecting OK will perform “Update Channel List”.
No channel found.
Please check aerial or local signal availability.
Press OK to start Auto Setup.
Follow the on screen instructions.
●
Please also refer to p. 99.
●
If channels are still not found, consult your local Panasonic dealer.
●
No module inserted
Check the CI module is inserted completely (p. 57).
●
No recording - Already recording
The equipment may already be recording.
●
No recording - Check media
The tape or disc may be “write protected”, full, missing or damaged.
●
No recording - Playing
The equipment may be playing the tape or disc.
●
No recording - Unknown reason
The recording may not be performed. Check the equipment.
●
No service
The broadcaster has stopped the service. Check the channel in the TV
●
Guide. (p. 20)
No signal
The TV cannot detect the signal. Check the connection of the RF cable.
●
Overcurrent error on USB device occurred.
Please remove the USB device, and switch
off the TV by mains power switch.
The connected USB device might cause overcurrent error. Follow the on
●
screen instructions.
Check if foreign objects are inside the USB port.
●
On screen messages