13
English
Select your country
≥
To continue using Voice Guidance, after selecting
your country, press [5] (numeric button). Make
settings for [Accessibility].
Select [Home]
Select [Home] for use in a home viewing environment.
≥
[Shop] is for shop display.
≥
To change the viewing environment later on, the set
will need to have all settings initialised by accessing
[Shipping Condition].
Set up the network connection
Tick the TV signal mode to tune, and then select
[Start Auto Setup]
≥
[Satellite Antenna Setup]
Ensure the satellite connections are completed (p. 8)
and select the tuner mode ([Dual Tuner] / [Single
Tuner]).
≥
[DVB-C Network Settings]
Normally set [Frequency] and [Network ID] to [Auto].
If [Auto] is not displayed or if necessary, enter
[Frequency] and [Network ID] specified by your cable
provider with numeric buttons.
Select your region
If tuning has failed check the Satellite cable, RF cable,
and the network connection, and then follow the on-
screen instructions.
<Note>
≥
The TV goes into Standby mode when no operation is
performed for 4 hours if [Auto Standby] in the Timer
menu is set to [On] (factory setting).
≥
The TV goes into Standby mode when no signal is
received and no operation is performed for 10 minutes
if [No signal Power off] in the Timer menu is set to [On]
(factory setting).
≥
To retune all channels
[Auto Setup] in [Tuning Menu] ([Setup] menu)
≥
To add the available TV signal mode later
[Set up TV Signals] ([Setup] menu)
≥
To initialise all settings
[Shipping Condition] in [System Menu] ([Setup]
menu)
FAQs
Before requesting service or assistance, please follow
these simple guides to solve the problem.
≥
For details, refer to [eHELP] (Support > FAQs).
The TV does not switch on
≥
Check the mains lead is plugged into the TV and the
mains socket.
≥
The fuse in the mains plug may have blown. Replace
it with one of an identical rating.
(p. 4)
The TV goes into Standby mode
≥
Auto power standby function is activated.
The remote control does not work or is intermittent
≥
Are the batteries installed correctly?
≥
Has the TV been switched on?
≥
The batteries may be running low. Replace them with
new ones.
≥
Point the remote control directly at the TV’s remote
control signal receiver (within about 7 m and a
30 degree angle of the signal receiver).
*
≥
Situate the TV away from sunshine or other sources of
bright light so they do not shine on the TV’s remote
control signal receiver.
*
≥
Is the remote control mode wrong?
(p. 11)
≥
If you are trying to use voice controls, is the remote
control registered (paired) with the TV?
(p. 10)
≥
If the solutions above do not fix the problem,
deregister (unpair) the remote control, then
register (pair) it again.
“When the remote
control does not respond” (p. 10)
When infrared communication is used
No image is displayed
≥
Check the TV is turned on.
≥
Check the mains lead is plugged into the TV and the
mains socket.
≥
Check the correct input mode is selected.
≥
Is [Backlight], [Contrast], [Brightness] or [Colour] in the
Picture menu set to the minimum?
≥
Check all required cables and connections are firmly
in place.
≥
Face the remote control at the TV, press and hold the
power button of the remote control for 10 seconds or
more, then release your finger to reboot the TV.
Auto Setup is now complete and the TV is
ready for viewing.
TX-55_65MX950B_OIB1_eng.book 13 ページ ２０２３年２月１５日 水曜日 午後２時２５分
