Panasonic Toughbook CF-W8EWDZZ2M Reference Manual Download

Page: 16 / 139

Using the Touchscreen

Install the touchscreen driver

If the touchscreen driver not installed, you can install the touchscreen driver using the following procedure.

Set [Touchscreen Mode] to [Auto] or [Tablet Mode] in the [Main] menu of the Setup Utility.

Press

F10

Click

(Start) and input [c:\util\drivers\tscreen\TPSetUp.exe] in [Start Search], and then

press

Enter

Follow the on-screen instructions.

Perform the touchscreen calibration (below).

Calibrating the Touchscreen

When you cannot point correctly with the stylus (include), calibrate the Touchscreen by following the steps below.

NOTE

Configure the Touchscreen for each account created.

Rotate the display to 0 degree before performing the calibration. (

page 18

)

Click

(Start) - [Control Panel] - [Additional Options] - [Tablet Calibration].

If [User Account Control] is displayed, click [Continue], or input password and click [OK].

Touch each

“

”

using the stylus.

“

”

is displayed in order at 9 locations.

Summary of Contents for Toughbook CF-W8EWDZZ2M












































































































































Search results

Summary of Contents for Toughbook CF-W8EWDZZ2M

Reviews:

Related manuals for Toughbook CF-W8EWDZZ2M

Brands by name

Popular brands

Panasonic Toughbook CF-W8EWDZZ2M, Reference Manual

Search results

Summary of Contents for Toughbook CF-W8EWDZZ2M

Reviews:

Related manuals for Toughbook CF-W8EWDZZ2M

Brands by name

Popular brands