Panasonic Toughbook CF-W8EWDZZ2M Reference Manual Download

Page: 18 / 139

Display Rotation

<Only for CF-T8 Series>

After Windows is started up, you can rotate the display and perform the Touch Pad and touchscreen operations in the rotated
mode.

Double-click

on the notification area or press

Alt

Each time this operation is performed, the screen display switches between the landscape mode (0 degree) and the
previously set angle (below).

To select the angle and rotate the display

Right-click

on the notification area, and then select the angle.

You can select rotation angles of 90, 180, or 270 degrees from the landscape mode.

NOTE

Be sure to use the above procedures to rotate the display.

By using the Display Rotation Tool, you can change the settings of the display rotation.

Right-click

on the notification area, and then click [Setting...].

Change the settings.

A. Changing the key combination

B. Changing the angle

(Default: 180 degrees)

Click [OK].

NOTE

If you shut down Windows when you rotate the display, the Touch Pad and touchscreen do not match the display angle
next time you start up Windows for a few seconds.

Rotating the Display

Changing the Settings

Summary of Contents for Toughbook CF-W8EWDZZ2M












































































































































Search results

Summary of Contents for Toughbook CF-W8EWDZZ2M

Reviews:

Related manuals for Toughbook CF-W8EWDZZ2M

Brands by name

Popular brands

Panasonic Toughbook CF-W8EWDZZ2M, Reference Manual

Search results

Summary of Contents for Toughbook CF-W8EWDZZ2M

Reviews:

Related manuals for Toughbook CF-W8EWDZZ2M

Brands by name

Popular brands