Panasonic TH-86SQE1W Operating Instructions (Functional Manual) Download Page 27

Page: 27 / 56

English

- 26 -

Quick Standby

If this feature is enabled the Display can be turned on again with the RS232 and LAN

commands if it is turned off through it. Press

Left

Right

button to enable or disable

the feature.
The Quick standby turns on the power quickly when the power is turned on.
ON: The power is turned on quickly when the power is turned on.
Off: The power is turned on normally when the power is turned on.

Note : When this setting is "On", the idle power consumption becomes higher.

Power on Delay

Sets a delay value at power on. This value can be set from 0 to 2000 ms in steps of 100

ms. The Display will turn on after the set delay time is expired.

Auto Launch

Configures the auto launch preference.

Open Browser(Open Browser initial page)

and

Disabled

options are available.

Boot Up Picture

Mode

Configures the picture mode preference at power on. If set as

Off

the last set picture

mode will be used at power on.

HDMI1 Wake Up

If this option is set as

Enabled

, the Display will turn on with the HDMI1 input source,

when it is switched on. This feature works based on HDMI 5V signal. When this signal

is active the Display wakes up and when the signal is inactive the Display shuts down.

You can disable this option by setting as

Disabled

In order to use this feature in

conjunction with the Auto Source Switch feature it is recommended to enable the

Auto Source Switch

option in the

Signage>Controls

menu.

If any Scheduler is set this option will be inactive and can not be set as

Enabled

HDMI2-HDMI3-

HDMI4 Wake Up

If this option is set as

Enabled

, the Display will turn on with the active input source

(HDMI2, HDM3 or HDMI4 depending on which input source is active), when it is switched

on. This feature works based on HDMI 5V signal. When this signal is active the Display

wakes up and when the signal is inactive the Display shuts down. You can disable this

option by setting as

Disabled

In order to use this feature in conjunction with the

Auto Source Switch feature it is recommended to enable the

Auto Source Switch

option in the

Signage>Controls

menu.

If any Scheduler is set this option will be inactive and can not be set as

Enabled

Note:

If multiple devices are connected to the Display through HDMI input sockets, this feature will not work.

The Display wakes up even if an input other than the last input is active.

Summary of Contents for TH-86SQE1W

























































Search results

Summary of Contents for TH-86SQE1W

Reviews:

Related manuals for TH-86SQE1W

Brands by name

Popular brands

Panasonic TH-86SQE1W, Operating Instructions (Functional Manual)

Search results

Summary of Contents for TH-86SQE1W

Reviews:

Related manuals for TH-86SQE1W

Brands by name

Popular brands