Panasonic TH-86EQ2W Operating Instructions Manual Download Page 8

8

English

CAUTION

Do not place any objects on top of the Display.

Ventilation should not be impeded by covering 

the ventilation openings with items such as 

newspapers, table cloths and curtains.

 •

Doing so may cause the Display to overheat, which 

can cause fire or damage to the Display.

For sufficient ventilation, see page 9.

Do not place the display where it may be affected by 

salt or corrosive gas.

 •

Doing so may cause the display to fall due to 

corrosion, and it may result in injury. Also, the unit 

may malfunction.

The following number of people are required to carry 

or unpack this unit.

86-inch model

 

75-inch model

:

4 or more

65-inch model

 

55-inch model

 

50-inch model

 

43-inch model

2 or more

86-inch model

 

75-inch model

 

65-inch model

:

Be sure to hold the handle, when carrying or moving 

the Display.

 •

If this is not observed, the unit may drop, resulting in 

injury.

When disconnecting the power supply cord, always 

pull on the plug (socket outlet side) / the connector 

(main unit side).

 •

Pulling the cord may damage the cord, and it may 

cause electric shock or fire due to short-circuit.

Be sure to disconnect all cables and overturn 

prevention accessories before moving the Display.

 •

If the Display is moved while some of the cables are 

still connected, the cables may become damaged, 

and fire or electric shock could result.

Disconnect the power supply plug from the wall 

socket as a safety precaution before carrying out 

any cleaning.

 •

Electric shocks can result if this is not done.

Do not step on, or hang from the display.

 •

They might tip over, or might be broken and it may 

result in injury. Pay special attention to the children.

Do not reverse the polarity (+ and -) of the battery 

when inserting.

 •

Mishandling the battery may cause its explosion 

or leakage, resulting in fire, injury or damage to 

surrounding properties.

 •

Insert the battery correctly as instructed. (see page 

13)

Do not use batteries with the outer cover peeling 

away or removed.

 •

Mishandling the batteries may cause the batteries 

to short circuit, resulting in fire, injury or damage to 

surrounding properties.

Remove the batteries from the remote control 

transmitter when not using for a long period of time.

 •

The battery may leak, heat, ignite or burst, resulting in 

fire or damage to surrounding properties.

Remove exhausted batteries from the remote control 

immediately.

 •

Leaving the batteries unattended in it may cause 

battery leakage, heat or burst.

Do not burn or breakup batteries.

 •

Batteries must not be exposed to excessive heat such 

as sunshine, fire or the like.

Do not turn the Display upside down.

Summary of Contents for TH-86EQ2W



































Reviews: