Panasonic Section 700 User Manual Download

Page: 315 / 394

Section 700-Operation

Appendix A. EX 1.0 Feature Update

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page A-25

Programming

See

Section 400 - Programming (Appendix C)

for more detailed

programming information.

Notes

• Serial Port 2 requires a special interface cable.

• Serial Port 2 can be used for Bus Monitor/Maintenance only. You must

continue to use the backplane port (Serial Port 1) for SMDR.

• Port selections are made from the Attendant phone as follows:

• When Serial Port 2 is used (i.e., #92 has been entered), the internal RAI

modem cannot be accessed.

T1 Networking

NOTE: The following information covers T1 Networking features that directly affect CPC-

EX operation. For detailed information regarding T1 Networking, see “T1
Networking Reference Guide”, Part No.550X10001, Section 540.

CPC-EX allows up to 4 DBS’s to be connected together via T1 interface to form a DBS
phone network. Such a network provides the following features:

•

Network Extension to Extension Calling

•

Call Forwarding to Network Extensions

•

Paging across Network nodes

•

Network Route selection

•

Remote DBS CO Access

•

SMDR Network Support

•

Independent Node Attendant Assignment

These feature are described in greater detail in the following sections.

Hardware Requirements

Each site (node) must contain the following hardware:

•

CPC-EX

to set Serial Port 1 for...

and Serial Port 2 for...

dial #90

Bus Monitor/Maintenance

no output

dial #92

SMDR

Bus Monitor/Maintenance

dial #93

SMDR/Maintenance

no output

Summary of Contents for Section 700











































































































































































































































































































































































































Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands

Panasonic Section 700, User Manual

Search results

Summary of Contents for Section 700

Reviews:

Related manuals for Section 700

Brands by name

Popular brands