Panasonic Section 700 User Manual Download | Manualshive

Page: 125 / 394

background image

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-9

For example, if an outside call on line 1 is sent to extension 135, but
extension 135 is busy or does not answer, the call will ring at the covering
phone and “TRK #01> 135” will appear on the covering phone’s display.

If two extensions are designated as covering phones and one of them is in
DND, the second will receive the call.

Call coverage assignments are controlled through system programming,
rather than from individual extensions.

For extension-controlled routing of unanswered calls, see “Call Forwarding”
on page 4-11.

Related Programming

• FF3 (Extension): Offhook Signal

• FF4 (Ringing and Hunt Groups): Call Coverage Group Member Table

Considerations

• Up to sixteen Call Coverage Groups can be programmed into your system.

A Call Coverage Group can have up to two covering phones and up to six
extensions.

• A member of one Call Coverage Group cannot belong to another Call

Coverage Group or to a Hunting Group.

• A Single-line telephone (SLT) or Digital Single Line telephone (DSLT)

can be a member of a coverage group, but cannot be a covering phone.

• Calls to an extension in DND do not cover.

• Calls to an extension with Call Forwarding activated do not cover.

• If the Call Forwarding feature or the Absence Message feature is activated

for covering phone No. 1, covering phone No. 2 will “cover” the other
extensions in the group.

• Voice intercom calls do not activate call coverage. Only tone intercom

calls can activate call coverage.

Call Duration Display

(All Versions)

Description

«
...
123
124
125
126
127
...
»

Summary of Contents for Section 700











































































































































































































































































































































































































Reviews:

No comments

Related manuals for Section 700

Brand: M2M Pages: 88

Brand: Wiko Pages: 164

EL 2310-08E Series

Brand: Oval Pages: 80

Brand: M2M Pages: 2

Brand: Snom Pages: 103

Brand: Alcatel Pages: 52

Brand: SMART Pages: 16

Brand: Maxcom Pages: 46

Brand: Sagem Pages: 61

Brand: T-Mobile Pages: 59

Brand: OUKITEL Pages: 60

Brand: Samsung Pages: 184

Brand: Samsung Pages: 184

Mi 11 Lite 5G NE

Brand: Xiaomi Pages: 9

Brand: Zte Pages: 60

Brand: Smartbox Pages: 84

Brand: Sigma Pages: 52

Brand: LG Pages: 1589

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands