Chapter 4
Settings — [PROJECTOR SETUP] menu
120 - ENGLISH
[COMMAND]
Detailed settings of
[COMMAND]
Description
[POWER ON]
―
Switches on the projector.
[STANDBY]
―
Enters standby.
[QUICK STARTUP]
[ON]
Enables the function of the [PROJECTOR SETUP] menu
→
[ECO
MANAGEMENT]
→
[QUICK STARTUP].
[OFF]
Disables the function of the [PROJECTOR SETUP] menu
→
[ECO
MANAGEMENT]
→
[QUICK STARTUP].
[SHUTTER]
[OPEN]
Disables the shutter function (shutter: open).
[CLOSE]
Enables the shutter function (shutter: closed).
[INPUT]
[RGB1]
Switches the input to RGB1.
[RGB2]
Switches the input to RGB2.
[VIDEO]
Switches the input to VIDEO.
[HDMI1]
Switches the input to HDMI1.
[HDMI2]
Switches the input to HDMI2.
[DIGITAL LINK]
Switches the input to DIGITAL LINK.
[MEMORY VIEWER]
Switches the input to MEMORY VIEWER.
[Panasonic APPLICATION]
Switches the input to Panasonic APPLICATION.
[MIRRORING]
*1
Switches the input to MIRRORING.
[INPUT1] - [INPUT10]
*2
Switches the input to DIGITAL LINK, and switches the input of the
Panasonic twisted-pair-cable transmitter to the specified input.
[LIGHT POWER]
[NORMAL]
Prioritizes luminance.
[ECO]
Controls the power to increase the life of the light source although
the luminance is lower than that of [NORMAL].
[QUIET]
Prioritizes the operation with less noise although the luminance is
lower than that of [NORMAL].
[IN STANDBY MODE(AUDIO)]
[OFF]
Stops the audio output during standby.
[ON]
Outputs the audio during standby.
[VOLUME]
[0] - [63]
Sets the volume.
*1 [MIRRORING] is displayed when the optional Wireless Module (Model No.: ET-WM300) is attached.
*2 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
11) Press the <ENTER> button.
f
The command is fixed and
n
is displayed at the left of the selected command.
f
After the command is fixed, press the <MENU> button to close the detailed setting screen.
12) Press
asqw
to select [STORE], and press the <ENTER> button.
Note
f
To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step
5)
is
displayed, or select [DELETE] at the screen in Step
6)
and press the <ENTER> button.
f
If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f
The operating time will be the local time. (
x
page 118)
f
If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
[RS-232C]
Set the communication condition of the <SERIAL IN> terminal. Refer to “<SERIAL IN> terminal” (
x
page 214).
1) Press
as
to select [RS-232C].
2) Press the <ENTER> button.
f
The
[RS-232C]
screen is displayed.
3) Press
as
to select [INPUT SELECT].
4) Press
qw
to switch the item.
[PROJECTOR]
Performs the RS-232C communication with the <SERIAL IN> terminal of the projector.
[DIGITAL LINK]
Performs the RS-232C communication via the optional DIGITAL LINK output supported device (Model
No.: ET-YFB100G, ET-YFB200G) and the <DIGITAL LINK/LAN> terminal.
