background image

Read this first!

ENGLISH - 

7

Important 

 

Information

CAUTION:

POWER

 

„

When disconnecting the power cord, be sure to hold the power plug and power connector.

If the power cord itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric 

shocks will result.

When not using the projector for an extended period of time, disconnect the power plug from the wall 

outlet.

Failure to do so may result in fire or electric shock.

Disconnect the power plug from the wall outlet before carrying out any cleaning and replacing the unit.

Electric shocks can result if this is not done.

ON USE/INSTALLATION

 

„

Do not put your weight on this projector.

You could fall or the projector could break, and injury will result.

Be especially careful not to let young children stand or sit on the projector.

 

z

Do not place the projector in extremely hot locations.

Doing so will cause the outer casing or internal components to deteriorate, or result in fire.

Take particular care in locations exposed to direct sunlight or near stoves.

 

z

Always disconnect all cables before moving the projector.

Moving the projector with cables still attached can damage the cables, which will cause fire or electric shocks 

to occur.

Never plug headphones and earphones into VARIABLE AUDIO OUT jack.

Excessive sound pressure from earphones and headphones can cause hearing loss.

ACCESSORIES

 

„

Do not use the old lamp unit.

If used it could cause lamp explosion.

If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the 

broken pieces.

Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and which 

contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces will cause injury.

If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek 

 

z

medical advice immediately.

Ask your dealer about replacing the lamp unit and check the inside of the projector.

 

z

When not using the projector for an extended period of time, remove the battery from the remote 

control.

Failure to observe this will cause the battery to leak, overheat, catch fire or explode, which may result in 

 

z

fire or contamination of surrounding area.

Do not open the desiccant bag or eat it, and do not discard it to moisture circumstances.

Accidentally swallow the contents of the desiccant bag may cause bad result to your body. Moreover, the 

contents may generate heat if exposing to moisture, so it may cause inflammation or injury to your skin if such 

contents is attached to your body or clothes.

In case that the desiccant has got into your eyes or mouth, wash with clean water immediately and seek 

 

z

medical advice.

Particular attention must be paid to children.

 

z

Summary of Contents for PT-LX300U































































Reviews: