23
ENGLISH
Fit the picture size to the screen size--- [Projector]
Fit the picture size to the screen size with the “ZOOM
(+/-)” buttons on the projector's rear control panel.
Repeat steps
through
until the picture
completely fits within the screen bounds.
Adjust focus again with the “FOCUS (+/-)” buttons
on the rear control panel or with the focus ring
on the projection lens.
Adjust the “ZOOM (+/-)” buttons again until the
picture completely fits within the screen bounds.
Powering Off the Projector
1. Press and hold the “POWER” button for more than
0.5 seconds or quickly double-press the button. The
projection lamp will turn off, with the power status
light turned to orange.
2. Wait until the power status light turns to red (i.e.,
until the cooling fan stops). While the cooling fan is
still running, never switch the MAIN POWER switch
OFF, unplug the projector from the outlet, or open
the main circuit breaker.
3. Press the “O” marked side of the MAIN POWER
switch to remove all power from the projector.
Starting to use
Powering Up the Projector
Remove the lens cover.
Plug one end of the accessory power cord into
the projector's power receptacle, and the other
end to a convenient wall outlet. (AC 220-240 V
50Hz/60 Hz)
Press the “ I ” marked side of the MAIN POWER
switch.
The projector will enter standby mode, with the power
status light lit in red.
Press the “POWER” button on the projector or
“POWER” button on the remote control.
The power indicator on the projector will flash orange.
After a shot period, the indicator will illuminate green.
Making Initial Adjustment /
Setting input port
Roughly adjust the focus with the “FOCUS (+/-)”
buttons on the rear control panel or with focus
ring on the projection lens.
Choose the projection scheme (page 34).
Select the input port with the “RGB” or “VIDEO”
button. --- [Projector or remote control]
Adjust volume level with the “VOLUME (+/-)”
buttons. --- [Remote control]
For volume level control on the projector, see page 27.
If your audio equipment is connected to the AUDIO OUT
jack, the VOLUME control adjusts the line output level.
Adjust the projector's tilt angle (page 24).
Adjust the vertical position of the picture (page 24)
Press the “AUTO SETUP” button --- [Projector or
remote control]
·
·
LEVELING Lever
on each side.
RE
MO
TE
RG
B O
UT
OU
T
WI
RE
D
IN
IN
OU
T
IN
R/R
-Y/
P
R
G/Y
SY
NC
/HD
VD
B/B
-Y/
P
B
IN
OU
T
OU
T
IN
R
L
US
B
SE
RIA
L
S-V
IDE
O I
N
AU
DIO
IN
RG
B
AU
DIO
AU
DIO
VID
EO
RG
B 2
IN
OU
T
IN
DV
I-D
RG
B 1
IN
> P
C <
TB
MU
152
·
RGB
VIDEO
RGB1(YP
B
P
R
1) RGB2(YP
B
P
R
2) DVI
S-VIDEO VIDEO
Note
• If the projector is re-powered while the
projection lamps are cooling down after the last
power off, the lamps will remain off for a short
time before they automatically turn on again
(Power Status light flashing in orange).
• The projector consumes approx. 9 Watts of
power in Standby mode after the cooling fan
stops (Power Status light lit in red).
• If you inadvertently shut off the Main Power
switch, the projection lamp may remain off for
some time on re-powering the projector. The
lamp will automatically turn on after a period of
time (Power Status light lit in green).
