background image

64

65

Other

s

DCF standard

This projector can only play back image files which comply with the DCF
specification. The DCF specification imposes the following conditions. Image
files or folders which do not conform to these conditions cannot be
recognised by the projector.

Limits on folder names 

Folders must be created as sub-folders of the DCIM folder on the SD
memory card.

B

Data which is contained within any folder other than the DCIM folder
cannot be recognised.

Folder names must consist of three numerals (folder number) followed
by five alphanumeric characters. (Example: 100abcde)

B

The three numerals must make up a number between 100 and 999, and
the alphanumeric characters can be taken from the following set of 37
characters: 0123456789abcdefghijklmnopqrstuvwxyz_ (No distinction is
made between upper-case and lower-case alphabetic characters.
Doublebyte characters cannot be used.)

Multiple folders using the same three-digit combination (folder number)
cannot be created.

B

For example, if two folders exist named "100abcde" and "100fghij"
respectively, the projector will not recognise them.

Folder sub-hierarchies are not supported.

B

For example, if a folder called "323fghij" is created as a sub-folder of the
"102abcde" folder, the projector will not be able to recognise the sub-
folder.

File names

File names must consist of four alphanumeric characters followed by
four numerals (file number), followed by ".jpg". (Example: abcd0001.jpg)

B

The four numerals must make up a number between 0001 and 9999, and
the alphanumeric characters can be taken from the following set of 37
characters: 0123456789abcdefghijklmnopqrstuvwxyz_ (No distinction is
made between upper-case and lower-case alphabetic characters.
Doublebyte characters cannot be used.)

Multiple file names using the same four-digit combination (file number)
cannot be created.

B

For example, if two files exist named "abcd0001.jpg" and "efgh0001.jpg"
respectively, the projector cannot recognise them normally.

File format

B

Only JPEG image files which comply with the Exif 2.2 standard are
recognised.

Dimensions

<Units: mm (˝)>

280(11)

80.2(3-5/32)

85.2(3-11/32)

PT

-L200U:

  278.5(10 15/16)

65.4(2 9/16)

49.7(1 15/16)

269(10-9/16)

PT

-L300U:

  279.7(11)

Trademark acknowledgements

B

The SD logo is a trademark.

B

VGA and XGA are trademarks of International Business Machines
Corporation.

B

Macintosh is a registered trademark of Apple Computer, Inc.

B

S-VGA is a registered trademark of the Video Electronics Standards
Association.

All other trademarks are the property of the various trademark owners.

Summary of Contents for PT-L300













































































Reviews: