Panasonic PT-FW430EA Operating Instructions Manual Download

Page: 21 / 89

ENGLISH -

Getting Started

Setting up

Projection method

You can use the projector with any of the following 4 projection methods. To set the desired method in the projector.

Mounting on the ceiling and

projecting forward

Setting on a desk/floor and

projecting from rear

(Using translucent screen)

Menu

Method

PROJECTION

METHOD

FRONT/CEILING

Menu

Method

PROJECTION

METHOD

REAR/DESK

Mounting on the ceiling and

projecting from rear

(Using translucent screen)

Setting on a desk/floor and

projecting forward

Menu

Method

PROJECTION

METHOD

REAR/CEILING

Menu

Method

PROJECTION

METHOD

FRONT/DESK

Refer to “PROJECTION METHOD” of “PROJECTION SETUP menu” (

pages 57) for details.

Attention

For optimum viewing quality, install the projector in a location where screen exposure to outside light, light from light fixtures

or other light is at a minimum. Also draw the curtains, close blinds and turn off light fixtures.

Do not use the projector installed vertically or tilted right or left. Use under such conditions could result in equipment

damage.

The projector must be installed so that its inclination to the horizontal plane is ±30° or less.

Installing the projector at an inclination that exceeds 30° may reduce product life or result in

malfunction.

Parts for ceiling mount (Optional)

You can install the projector on the ceiling using the optional ceiling mount bracket (ET-PKF110H: for high ceiling,

ET-PKF110S½ for low ceiling).

Use only the ceiling mount brackets specified for this projector.

Refer to the installation manual for the ceiling mount bracket when you install the bracket and the projector.

Be sure to consult your dealer when using the ceiling mount bracket for the PT-F300U/PT-FW300U (ET-

PKF100H for high ceilings or ET-PKF100S for low ceilings).

Attention

To ensure projector performance and security, installation of the ceiling mount bracket must be carried by your

dealer or a qualified technician.

Summary of Contents for PT-FW430EA


























































































Search results

Summary of Contents for PT-FW430EA

Reviews:

Related manuals for PT-FW430EA

Brands by name

Popular brands

Panasonic PT-FW430EA, Operating Instructions Manual

Search results

Summary of Contents for PT-FW430EA

Reviews:

Related manuals for PT-FW430EA

Brands by name

Popular brands