Panasonic PT-AH1000, Specifications

Page: 10 / 11

S
P E C
F
I L E
PT- AH1000
Full High-Definition Home Cinema Projector
As of December 2011
SFL11M010-1
1 0 / 1 1
Status request commands
Q P W
Q I N
Q P M
Q S H
Q F Z
Q O T
Q W M
Standby power status
Input signal status
Picture mode status
Blank function status
Freeze function status
Off timer status
Waveform monitor statusutton
0 0 0 = o f f , 0 0 1 = o n
C P 1 = c o m p o n e n t , S V D = S - v i d e o , V I D = v i d e o ,
H D 1 = H D M I 1 , H D 2 = H D M I 2 , R G 1 = c o m p u t e r
N O R = n o r m a l , D Y N = d y n a m i c , G M 1 = g a m e 1 ,
S P T = s p o r t s , 7 0 9 = R e c . 7 0 9 , C N 1 = c i n e m a 1 ,
V C N = v i v i d c i n e m a
0 = o f f , 1 = o n
0 = o f f , 1 = o n
0 = o f f , 1 = 6 0 m i n , 2 = 9 0 m i n , 3 = 1 2 0 m i n ,
4 = 1 5 0 m i n , 5 = 1 8 0 m i n , 6 = 2 1 0 m i n ,
7 = 2 4 0 m i n
0 = o f f , 1 = f u l l s c a n ( Y ) , 2 = f u l l s c a n ( R ) ,
3 = f u l l s c a n ( G ) , 4 = f u l l s c a n ( B ) ,
5 = s i n g l e l i n e s c a n ( Y ) , 6 = s i n g l e l i n e s c a n ( R ) ,
7 = s i n g l e l i n e s c a n ( G ) , 8 = s i n g l e l i n e s c a n ( B )
Q V X : A G O S 0 = p 1 p 2
A G O S 1 = p 1 p 2
A G O S 2 = p 1 p 2
A G O S 3 = p 1 p 2
A G I S 0 = p 1 p 2
Gamma output level (Y)
Gamma output level (R)
Gamma output level (G)
Gamma output level (B)
Gamma input level
A G O S 0 = p 1 p 2 d 1 d 2 d 3 d 4
p 1 p 2 = p o i n t n u m b e r : 0 1 – 0 9
d 1 d 2 d 3 d 4 = o u t p u t : 0 0 0 0 – 0 2 5 5
A G O S 1 = p 1 p 2 d 1 d 2 d 3 d 4
p 1 p 2 = p o i n t n u m b e r : 0 1 – 0 9
d 1 d 2 d 3 d 4 = o u t p u t : 0 0 0 0 – 0 2 5 5
A G O S 2 = p 1 p 2 d 1 d 2 d 3 d 4
p 1 p 2 = p o i n t n u m b e r : 0 1 – 0 9
d 1 d 2 d 3 d 4 = o u t p u t : 0 0 0 0 – 0 2 5 5
A G O S 3 = p 1 p 2 d 1 d 2 d 3 d 4
p 1 p 2 = p o i n t n u m b e r : 0 1 – 0 9
d 1 d 2 d 3 d 4 = o u t p u t : 0 0 0 0 – 0 2 5 5
A G I S 0 = p 1 p 2 d 1 d 2 d 3
p 1 p 2 = p o i n t n u m b e r : 0 1 – 0 9
d 1 d 2 d 3 = i n p u t : 0 0 1 – 0 9 9
Command
Option Menu Command
Description Parameter
Command example
To set the input to HDMI 1, send the command as shown below.
STX
Start Command Parameter End
IIS : HD1 ETX
NOTE: When sending commands without parameters, a colon (:) is not necessary.
NOTE: If a wrong command is received, the projector will send an ER401 or ER402 command to the computer.