Panasonic PT-56TWD63 Operating Manual Download Page 6

Page: 6 / 88

NSTALLATION

ENGLISH

Installation

Television Location

This unit can be used as part of an entertainment center.
Consult your dealer for available options.

•

Avoid excessive sunlight or bright lights, including
reflections.

•

Keep away from excessive heat or moisture. Inadequate
ventilation may cause internal component failure.

•

Fluorescent lighting may reduce remote control
transmitting range.

•

Keep away from magnetic equipment, including motors,
fans and external speakers.

Component Connection Cables

Shielded audio and video cables should be used between
components. For best results:

•

Use 75-ohm coaxial shielded cables.

•

Use appropriate input and output connectors, that match
your component connectors.

•

Avoid long cables to minimize interference.

AC Power Supply Cord

CAUTION:

TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT
OF AC OUTLET AND FULLY INSERT. DO NOT
USE A PLUG WITH A RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADE CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.

PROTECT POWER CORDS FROM BEING WALKED ON, ROLLED
OVER, CRIMPED, BENT, OR PINCHED, PARTICULARLY AT PLUGS,
CONVENIENCE RECEPTACLES, AND THE POINT WHERE THEY EXIT
FROM THE APPARATUS.

Cable / Antenna Connection

For proper reception of analog or digital cable channels, a
cable service connection is required.

Cable Connection

Connect the cable supplied by your local
cable company to ANTENNA (A)
connection on back of television. Select
Cable mode and ANTENNA (A) in SET UP
menu under Program CH (Program
Channels).

Antenna Connection

•

For proper reception of digital and analog VHF/

UHF channels, an external antenna is required. For
best reception an outdoor antenna is
recommended.

•

Connect home antenna to

either ANT (A) or ANT (B)
connection on

back of the

television. Select Antenna
mode for ANTENNA (A) or
(B) in Input Setup under
Program CH in Setup menu.

Note:

Cable Mode is preset at the factory. Antenna users must
change to ANTENNA Mode for ANTENNA (A) in the Set
Up menu. If you have both Cable and Antenna, the
Cable

must

be connected to ANT (A).

First Time Setup

For your convenience, First Time Set up menu will be

displayed on screen when the set is turned on for the first

time. If needed, follow the menus and procedures

displayed on-screen for setting up the features.

Input Setup

To select the configuration of RF input depending on the

signal source.

Note:

No video will be displayed in this setup mode.

Procedure

•

Press

VOL

to select Cable only, Cable/Antenna or

Antenna only.

•

Press the

button to underline your selection.

•

When the next screen is displayed, press

button to

start the Auto Scan. All available channels with a signal
will be programmed into memory.

Auto Scan

This feature allows you to selectively auto scan channels.

You can Scan All, Analog only channels or Analog & Digital

channels.

Procedure

•

Press

button to start Auto Scan.

•

After Auto Scan is completed the PTV tunes to the first
channel found during auto scan.

Notes:

•

If the EXIT button is pressed at anytime during auto
scan, the First Time Setup menu will be cancelled and
the PTV will tune to analog channel 2 on ANTENNA (A).

•

If a DCM (Digital Cable Module) is present during the
First Time Setup and Antenna (A) is set to cable,
Antenna (A) will not be scanned due to the DCM
providing the channel map.

Convergence

This menu lets you set the green CRT alignment and the center
convergence. Follow the instructions on-screen to perform
convergence. After convergence is performed, press

EXIT

return to normal viewing.

Polarized plug

75 Ohm ANT A

Incoming Cable from

Cable Company

Incoming Cable from

Home Antenna

First time setup

Input Setup

Manual Program

Signal Meter