Panasonic NV-MD10000, Service Manual

Page: 49 / 101

49
LVL LPF Switch for Auto Focus
M M1-3 Motor Coil Terminal 1 to 3
MA0-5 Microprocessor Address Data 0-5
Mbps Megahertz Bit Per Second
MD Modulation
MD0-7 Microprocessor Data 0-7
MDT0-7 Microprocessor Data 0-7
ME (TAPE) Metal Evaporated (Tape)
MENB Focus Motor Enable
MFF Manual Focus Far
MFN Manual Focus Near
MHSYNC Monitor Horizontal Sync Signal
MIC Memory In Cassette
MIG Meta In Gap
MIX N.R.D. Non Rec Data Mix
MOD Modulation
MOUT Mic Out
MP (TAPE) Metal Particle (Tape)
MPEG Moving Picture Image Cording Experts Group
MPEG2 Moving Picture Image Cording Experts Group Phase 2
MRST Focus Motor Reset
MSB Most Signal Bit
MVSYNC Monitor Vertical Sync Signal
N N/F Near/Far Focus
N/P NTSC/PAL
NB1-3 Base for NPN Transistor
NC No Connection
NC1-3 Corrector of NPN Transistor
NCLR Power On Reset
NCP1 Clamp Pulse
NCP2+VDH Clamp Pulse + Horizontal Drive Pulse
NCP2+VDM Clamp Pulse + Gate Pulse
NDE Non Liner De-Emphasis
NE Emitor of NPN Transistor
NLE Non Liner Emphasis
NR Noise Reduction
NRD Non Rec Data
NRD BLK Non Rec Data Blanking
NRD CLK No Rec Data Clock
NRE Read Enable Input (Low Active)
NWE Write Enable (Low Active)
O OB Optical Black
OBCNT Optical Black Control
OBREF Reference Voltage for Optical Black Control
OE Output Enable
OFH Horizontal Counted Down Clock Signal (Reference)
OFS Offset
OP Operation AMP Output
OSD ON Screen Display
OVL Overlap Pulse
OZ Optical Zoom
P P SW Power Switch
PB1-3 PNP Base 1-3
PBCTL Play Back Control
PBCTL Pre-Branking Control
PBH Head Amp Switch
PBLK Pre-Blanking (Pulse)
PC1-3 Corrector of PNP Transistor
PCBM Carrier Balance
PCH Phase Compensator (Hall AMP)
PCI Phase Compensator (Current)
PCO Phase Compensator Out
PCS Switching Power Control
PCV Phase Compensator (Voltage)
PE Emitter of PNP Transistor
PED Pedestal
PEDECNT Pedestal Control
PENO Alarm (L)
PFP Pilot Frame Position
PGA, B Power Ground A, B
PGC Pulse Generator Comparator
PGI Pulse Generator Input
PGMM Pulse Generator Monostable Multivibrator
PGO Output of Pulse Generator AMP
PMODE Select Signal for Normal / Wide Screen
PON Power On
POR Power On Reset
POSCOM Common Position
PREAMP Pre-AMP
PREBLK Pre-Blanking
PT Protect for V Voltage
PWM Pulse Width Modulation
PWMB Pulse Width Modulation Pulse
Q Q2H Source Output Select
R R CTL P Recorded Control Pulse (+)
R CTL R Recorded Control Pulse (–)
R/B Read/Busy
R/L Direction Control for Data Transmition
RA Recording AMP
RA1 Rec AMP 1
RAC AC Rec Audio Current
RAD Read Address Data
RAE Read Address Enable
RB Read Busy
R-B R Bias
RCB R Carrier Balance
RE Read Enable
RE(F), (S) Rotary Erase Head Transformer
REB R Bias
REC CC Rec Current Control
REC CCNT Rec Current Control
RECCTRL Recording Control Pulse
RECI Rec Amp Switch
INITIAL/LOGO INITIAL/LOGO ABBREVIATIONS ABBREVIATIONS