Panasonic NR-B32FE2 Service Manual Download | Manualshive

Page: 14 / 63

background image

14

2. The setting temperature

The temperature, when it set on 4

°

C.

The OFF/ON temperature value corresponding to each ATC temperature is as shown in the next graph.

5.1.3.

SC temperature control

The twin damper motor is turned on and off detecting the SCC temperature.
The temperature, when it set on 2

°

C.

The OFF/ON temperature value corresponding to each ATC temperature is as shown in the next graph.

«
...
12
13
14
15
16
...
»

Summary of Contents for NR-B32FE2
































































Reviews:

No comments

Related manuals for NR-B32FE2

Brand: Samsung Pages: 2

CLASSIC RH423LDBI

Brand: Dometic Pages: 60

Brand: Gorenje Pages: 40

Brand: Bauknecht Pages: 13

Brand: Matrix Pages: 24

Brand: Summit Professional Pages: 36

Brand: Parmco Pages: 7

Brand: Qilive Pages: 180

Brand: Insignia Pages: 23

Brand: Personal Chiller Pages: 8

Brand: Gram Pages: 47

Brand: Reeva Pages: 17

U-1224FZRINT-00A

Brand: U-Line Pages: 53

Brand: HAEGER Pages: 56

Brand: V-ZUG Pages: 120

Brand: Samsung Pages: 42

RFG297HD SERIES

Brand: Samsung Pages: 80

Brand: Samsung Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands