background image

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6

6

4.3.

Power consumption and current

The following requirements shall be met in accordance with Product Standard.

(1) Washing

Note : To determine the value, integrate the data for 2 min after 5 min from starting motor and convert based on duty ratio of
water flow for that period.

(2) Spinning

Note : To determine the value, integrate the data for 2.5 min after 3.5 min from starting motor and convert based on duty ratio of
water flow for that period.

Model

Voltage

Frequency

Power source

Water load

Rated load

NA-F75G6/S6

230V

50Hz

Current (A)

1.7 + 0.4

2.15 + 0.5

Power consumption (W)

340 + 80

430 + 50

NA-F70G6/S6

230V

50Hz

Current (A)

1.7 + 0.4

2.15 + 0.5

Power consumption (W)

340 + 80

423 + 50

NA-F65G6

230V

50Hz

Current (A)

1.7 + 0.4

2.15 + 0.5

Power consumption (W)

340 + 80

408 + 50

NA-F62G6

230V

50Hz

Current (A)

1.7 + 0.4

2.15 + 0.5

Power consumption (W)

340 + 80

400 + 50

Model

Voltage

Frequency

Power source

No load

Rated load

NA-F75G6/S6
NA-F70G6/S6
NA-F65G6
NA-F62G6

230V

50Hz

Current (A)

0.9 + 0.2

1.1 + 0.2

Power consumption (W)

215 + 50

250 + 50

Summary of Contents for NA-F75G6

































Reviews: