26
1) About "*" indication:
The third digit from the left is different as follows.
In case of 0 (example: 18
0
01000)
When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been completed.
It means that this error is occurred basically at user side.
In case of 8 (example: 18
8
01000)
When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?50"):
The third digit from the right shows one of the hexadecimal ("0" to "F") character.
4.
How to returned to Normal Display:
Turn the power off and on, to exit from Error code display mode.
Note:
The error code can not be initialized.
HARD
VENUS A/
D
Flash
28*0
0000
Flash charging error.
STRB CHG
FLASH TOP
P.C.B./FPC
IC6001-(AC17) signal line or Flash charging circuit
FLASH
ROM
(EEPROM
Area)
FLASH
ROM
(EEPROM
Area)
2B*0
0001
0003
0004
EEPROM read error
FROM RE
FROM
IC6002 (FLASH ROM)
0002
EEPROM write error
FROM WR
FROM
IC6002 (FLASH ROM)
0005
Firmware version up error
(No indication) (No indication)
Replace the firmware file in the SD memory card.
0008
SDRAM error
0009
SDRAM Mounting defective
SYSTEM
RTC
2C*0
0001
SYSTEM IC initialize failure error
SYS INIT
MAIN P.C.B.
Communication between IC6001 (VENUS 4) and
IC9101 (SYSTEM)
SOFT
CPU
Reset
30*0
0001
|
0007
NMI reset
Non Mask-able Interrupt
(30000001-30000007 are caused by factors)
NMI RST
MAIN P.C.B.
Card
Card
31*0
0001
Card logic error
SD CARD
SD CARD/
DSP
SD memory card data line or IC6001 (VENUS 4)
0002
Card physical error
SD memory card data line or IC6001 (VENUS 4)
0004
Write error
SD WRITE
SD memory card data line or IC6001 (VENUS 4)
39*0
0005
Format error
INMEMORY
FROM
CPU,
ASIC hard
Stop
38*0
0001
Camera task finish process time out.
LENS COM
LENSu/DSP
Communication between Lens system and IC6001
(VENUS 4)
0002
Camera task invalid code error.
DSP
DSP
IC6001 (VENUS 4)
0100
File time out error in recording motion image
IC6001 (VENUS 4)
0200
File data cue send error in recording motion image
IC6001 (VENUS 4)
0300
Single or burst recording brake time out.
Memory
area
3A*0
0008
USB work area partitioning failure
(No indication) (No indication)
USB dynamic memory securing failure when connect-
ing
Operation
Power on
3B*0
0000
FLASHROM processing early period of camera during
movement.
INIT
(No indication)
Zoom
Zoom
3C*0
0000
Imperfect zoom lens processing
ZOOM
ZOOMm/
LENSu
Zoom lens
35*0
0000
|
FFFF
Software error
(0-7bit : command, 8-15bit : status)
DSP
DSP
35*1
0000
Though record preprocessing is necessary, it is not
called.
35*2
0000
Though record preprocessing is necessary, it is not
completed.
(No indication) (No indication)
Attribute
Main item
Sub item
Error code
Contents (Upper)
Error Indication
High 4bits Low 4 bits
Check point (Lower)
Detecting
device
Part/Circuit
Summary of Contents for Lumix DMC-FT10EB
