Panasonic KX-UT670 Administrator'S Manual Download Page 88

Page: 88 / 250

4.6.1.1 SIP Setting

SIP User Agent

Description

Specifies the text string to send as the user agent in the headers of SIP
messages.

Value Range

Max. 40 characters

Note

•

You cannot leave this field empty.

•

If "{mac}" is included in this field, it will be replaced with the
unit’s MAC address in lower-case.

•

If "{MAC}" is included in this field, it will be replaced with the
unit’s MAC address in upper-case.

•

If "{MODEL}" is included in this field, it will be replaced with the
unit’s model name.

•

If "{fwver}" is included in this field, it will be replaced with the
firmware version of the unit.

Default Value

Panasonic_{MODEL}/{fwver} ({mac})

Configuration File Reference

SIP_USER_AGENT (Page 188)

4.6.2 SIP Settings [Line 1]–[Line 6]

This screen allows you to change the SIP settings that are specific to each line.

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands