Panasonic KX-UT670 Administrator'S Manual Download Page 114

Page: 114 / 250

Unconditional (Phone Number)

Description

Specifies the phone number of the destination to forward all incoming
calls to.

Note

•

If you change this setting when

[Synchronize Do Not Disturb

and Call Forward]

is set to

[Yes]

, the change to this setting is

not immediately applied on this screen. In this case, reload the
screen to confirm that the change is applied.

Value Range

Max. 32 characters

Note

•

You cannot leave this field empty if

[Unconditional (Enable

Call Forward)]

is set to

[Yes]

Default Value

Not stored.

Busy (Enable Call Forward)

Description

Selects whether to forward incoming calls to a specified destination
when the line is in use.

Note

•

If Do Not Disturb has been enabled on the server, the server
rejects incoming calls and the unit does not receive any calls,
even if you have selected

[Yes]

for this setting.

•

If you have selected

[Yes]

for this setting and Call Forward has

been enabled on the server, but the forwarding destinations
differ, incoming calls are forwarded to the destination set on the
server.

•

If Call Forward has been enabled on the server, incoming calls
are forwarded to the destination set on the server, even if you
have selected

[No]

for this setting.

•

You can synchronize the Do Not Disturb and Call Forward
settings from the Web user interface (

see

[Synchronize Do

Not Disturb and Call Forward]

4.7.2.1 Call Control

) or

through configuration file programming (

see

FWD_DND_SYNCHRO_ENABLE_n

" in

5.8.1 Call Control

Settings

•

If you change this setting when

[Synchronize Do Not Disturb

and Call Forward]

is set to

[Yes]

, the change to this setting is

not immediately applied on this screen. In this case, reload the
screen to confirm that the change is applied.

Value Range

•

Yes

•

Default Value

114

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands