Panasonic KX-UT670 Administrator'S Manual Download Page 184

Page: 184 / 250

Web User Interface Reference

Supports RFC 2543 (c=0.0.0.0) (Page 103)

DTMF_SIGNAL_LEN

Value Format

Integer

Description

Specifies the length of the DTMF signal, in milliseconds.

Value Range

60–200 (in 5 millisecond units)

Default Value

180

DTMF_INTDIGIT_TIM

Value Format

Integer

Description

Specifies the interval, in milliseconds, between DTMF signals.

Value Range

60–200 (in 5 millisecond units)

Default Value

5.8 Line Settings

5.8.1 Call Control Settings

DISPLAY_NAME_n

Parameter Name Example

DISPLAY_NAME_1

DISPLAY_NAME_2

, …,

DISPLAY_NAME_6

Value Format

String

Description

Specifies the name to display as the caller on the other party’s phone
when you make a call.

Value Range

Max. 24 characters

Note

•

You can use Unicode characters for this setting.

Default Value

Empty string

Web User Interface Reference

Display Name (Page 109)

VM_NUMBER_n

Parameter Name Example

VM_NUMBER_1

VM_NUMBER_2

, …,

VM_NUMBER_6

Value Format

String

184

Administrator Guide

Document Version 2012-07

Section 5 Configuration File Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands