manualshive.com logo in svg

Panasonic KX-TGF852, Operating Instructions Manual, Page: 56 / 76

Share
Download
Panasonic KX-TGF852 Operating Instructions Manual Download Page 56

Display message

Cause/solution

Check tel line

R

The supplied telephone line cord has not been connected yet or
not connected properly. Check the connections (page 9).

Checking

R

The automated call block function is in operation. Try again later.

Error!!

R

Recording was too short. Try again.

Memory full

R

The recording memory is full. Erase unwanted recordings
(page 48).

Invalid

R

There is no handset registered to the base unit matching the
handset number you entered.

R

The handset is not registered to the base unit. Register the
handset (page 43).

Requires
subscription
to Caller ID.

R

You must subscribe to a Caller ID service. Once you receive
caller information after subscribing to a Caller ID service, this
message will not be displayed.

Use rechargeable
battery.

R

A wrong type of battery such as alkaline or manganese was
inserted. Use only the rechargeable Ni-MH batteries noted on
page 4, 6.

Troubleshooting

If you still have difficulties after following the instructions in this section, disconnect the base unit’s AC
adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset, and then
insert them into the handset again.
If the base unit batteries for power backup are installed, remove the batteries from the base unit, and
then insert them into the base unit again.

General use

Problem

Cause/solution

The handset does not turn on
even after installing charged
batteries.

R

Place the handset on the charger to turn on the handset.

The unit does not work.

R

Make sure the batteries are installed correctly (page 9).

R

Fully charge the batteries (page 10).

R

Check the connections (page 9).

R

Unplug the base unit’s AC adaptor to reset the unit. Reconnect
the adaptor and try again.

R

The handset has not been registered to the base unit. Register
the handset (page 43).

I cannot hear a dial tone.

R

The base unit’s AC adaptor or telephone line cord is not
connected. Check the connections.

R

Disconnect the base unit from the telephone line and connect
the line to a known working telephone. If the working telephone
operates properly, contact our service personnel to have the
unit repaired. If the working telephone does not operate
properly, contact your phone service provider.

The base unit beeps.

R

New messages have been recorded. Listen to the new
messages (page 48).

56

For assistance, please visit http://shop.panasonic.com/support

Useful Information

TGF85x_(en)_1023_ver001.pdf   56

10/23/2019   1:26:12 PM

Summary of Contents for KX-TGF852













































































Reviews:

No comments