Panasonic KX-TGA641FXS Service Manual Download

Page: 96 / 101

KX-TG6411FXS/KX-TG6411FXT/KX-TG6412FXS/KX-TG6412FXT/KX-TGA641FXJ/KX-TGA641FXS/KX-TGA641FXT

15.5. Replacement Part List

1. RTL (Retention Time Limited)

Note:

The “RTL” marking indicates that its Retention Time is
Limited.
When production is discontinued, this item will con-
tinue to be available only for a specific period of time.
This period of time depends on the type of item, and
the local laws governing parts and product retention.
At the end of this period, the item will no longer be
available.

2. Important safety notice

Components identified by the mark indicates special
characteristics important for safety. When replacing any
of these components, only use specified manufacture’s
parts.

3. The S mark means the part is one of some identical parts.

For that reason, it may be different from the installed part.

4. ISO code (Example: ABS-94HB) of the remarks column

shows quality of the material and a flame resisting grade
about plastics.

5. RESISTORS & CAPACITORS

Unless otherwise specified;
All resistors are in ohms (

Ω

) k=1000

Ω

, M=1000 k

Ω

All capacitors are in MICRO FARADS (

F)p=

µµ

*Type & Wattage of Resistor

15.5.1. Base Unit

15.5.1.1. Cabinet and Electrical Parts

15.5.1.2. Main P.C.Board Parts

Note:

(*1) When replacing IC7, IC401 or X1, make the adjustment
using PNZZTG6411FX. Refer to

How to download the

data

(P.65) of

Things to Do after Replacing IC or X'tal.

(*2) When you removing E1, use special tools (ex. Hot air
disordering tool).
(*3) Backside of this IC has a ground plate.
(*4) Supplied IC is Flat Package Type.

Safety Ref.

No.

Part No.

Part Name & Description Remarks

PNKM1073Y4

CABINET BODY (for KX-
TG6411FXS)

PS-HB

PNKM1073Y1

CABINET BODY (for KX-
TG6411FXT)

PS-HB

PNKE1030Z3

CASE, CHARGE TERMINAL
(for KX-TG6411FXS)

PS-HB

PNKE1030Z1

CASE, CHARGE TERMINAL
(for KX-TG6411FXT)

PS-HB

PNBC1268Z1 BUTTON, LOCATOR

ABS-HB

K2ECYZ000001 JACK, DC

PQJJ1T039Y JACK, MODULAR

PNJT1025Z CHARGE TERMINAL

PNLA1002Z ANTENNA

PNYE1009Z SPACER, ANTENNA

PNKF1055Z2 CABINET COVER (for KX-

TG6411FXS)

PS-HB

PNKF1055Z1 CABINET COVER (for KX-

TG6411FXT)

PS-HB

PQHA10023Z RUBBER PARTS,FOOT CUSH-

ION

PNGT2123Y

NAME PLATE (for KX-
TG6411FXS)

PNGT2123Z

NAME PLATE (for KX-
TG6411FXT)

Safety Ref.

No.

Part No.

Part Name & Description Remarks

PCB1

PNWPG6411FXH

MAIN

P.C.BOARD

ASS'Y

(RTL)

(ICs)

IC1

C0CBAYG00016 IC S

IC7

C1CB00002906 IC

(BBIC(FLASH))

(*1)(*3)(*4)

IC401 PQWICD300EHR IC (EEPROM) (*1)

IC801 C1CB00001842 IC (*3)

(TRANSISTORS)

B1ABCE000009 TRANSISTOR(SI)

B1ACGP000008 TRANSISTOR(SI)

PQVTBF822T7 TRANSISTOR(SI)

2SD0874AS TRANSISTOR(SI)

B1ADGE000004 TRANSISTOR(SI)

(DIODES)

B0JCME000035 DIODE(SI)

B0EDER000009 DIODE(SI)

MA111 DIODE(SI) S

D22

B0ECKM000008 DIODE(SI)

D23

MA8220 DIODE(SI) S

D26

MANV250GEL DIODE(SI)

DA801 B0DDCD000001 DIODE(SI)
DA802 B0DDCD000001 DIODE(SI)

(COILS)

PQLQXF330K COIL S

L801

G1C27NJ00010 COIL

L802

G1C3N0ZA0063 COIL

L803

G1C3N0ZA0063 COIL

(COMPONENT PARTS)

RA1

D1H810240004 RESISTOR ARRAY

RA402 D1H410320002 RESISTOR ARRAY

RA80

D1H422120001 RESISTOR ARRAY

(VARISTOR)

SA1

J0LF00000026 VARISTOR

(SURGE

ABSORBER)

(RESISTORS)

PQ4R10XJ184 180k S

PQ4R10XJ105 1M S

PQ4R10XJ184 180k S

PQ4R10XJ105 1M S

ERJ3GEYJ565 5.6M

ERJ3GEYJ104 100k

ERJ3GEYJ565 5.6M

R10

ERJ3GEYJ104 100k

R12

ERJ2GEJ103 10k

Safety Ref.

No.

Part No.

Part Name & Description Remarks

Summary of Contents for KX-TGA641FXS






































































































Search results

Summary of Contents for KX-TGA641FXS

Reviews:

Related manuals for KX-TGA641FXS

Brands by name

Popular brands

Panasonic KX-TGA641FXS, Service Manual

Search results

Summary of Contents for KX-TGA641FXS

Reviews:

Related manuals for KX-TGA641FXS

Brands by name

Popular brands