Panasonic KX-TG6643B Operating Instructions Manual Download Page 51

Page: 51 / 68

Error messages

Display message

Cause/solution

Base no power

No link. Re-connect
base AC adaptor.

No link.

The handset has lost communication with the
base unit. Move closer to the base unit and try
again.

Unplug the base unit’s AC adaptor to reset the
unit. Reconnect the adaptor and try again.

The handset’s registration may have been
canceled. Re-register the handset (page 33).

When “

No link.

” is displayed during a

power failure, place a handset on the base
unit to supply power to the base unit.

Busy

The called unit is in use.

Other units are in use and the system is busy.
Try again later.

The handset you are using is too far from the
base unit. Move closer and try again.

Call phone company for
your access #

You have not stored the voice mail access
number. Store the number (page 45).

Check tel line

The supplied telephone line cord has not been
connected yet or not connected properly.
Check the connections (page 9).

Error!!

Recording was too short. Try again.

Invalid

There is no handset registered to the base
unit matching the handset number you
entered.

The handset is not registered to the base unit.
Register the handset (page 33).

Requires subscription
to Caller ID.

You must subscribe to a Caller ID service.
Once you receive caller information after
subscribing to a Caller ID service, this
message will not be displayed.

Use rechargeable
battery.

A wrong type of battery such as Alkaline or
Manganese was inserted. Use only the
rechargeable Ni-MH batteries noted on page 4,
6.

For assistance, please visit http://www.panasonic.com/help

Useful Information

Summary of Contents for KX-TG6643B





































































Search results

Summary of Contents for KX-TG6643B

Reviews:

Related manuals for KX-TG6643B

Brands by name

Popular brands

Panasonic KX-TG6643B, Operating Instructions Manual

Search results

Summary of Contents for KX-TG6643B

Reviews:

Related manuals for KX-TG6643B

Brands by name

Popular brands