manualshive.com logo in svg

Panasonic KX-TG6521BXB, Service Manual

Share
Download
Panasonic KX-TG6521BXB Service Manual Download Page 80

80

KX-TG6521BXB/KX-TGA651BXB

15.4. Replacement Part List

1. RTL (Retention Time Limited)

Note:

The “RTL” marking indicates that its Retention Time is
Limited. 
When production is discontinued, this item will
continue to be available only for a specific period of
time. This period of time depends on the type of item,
and the local laws governing parts and product
retention.
At the end of this period, the item will no longer be
available.

2. Important safety notice

Components identified by the   mark indicates special
characteristics important for safety. When replacing any
of these components, only use specified manufacture’s
parts.

3. The S mark means the part is one of some identical parts.

For that reason, it may be different from the installed part.

4. ISO code (Example: ABS-94HB) of the remarks column

shows quality of the material and a flame resisting grade
about plastics.

5. RESISTORS & CAPACITORS

Unless otherwise specified;
All resistors are in ohms (

Ω

) k=1000 

Ω

, M=1000 k

Ω

All capacitors are in MICRO FARADS (

µ

F)p=

µµ

F

*Type & Wattage of Resistor

15.4.1. Base Unit

15.4.1.1. Cabinet and Electrical Parts

15.4.1.2. Main P.C.Board Parts

Note:

(*1) When replacing IC7, IC401 or X1, make the adjustment
using PNZZTG6521BX. Refer to 

How to download the

data

 (P.53) of 

Things to Do after Replacing IC or X'tal.

(*2) When removing E1, use special tools (ex. Hot air
disordering tool).
(*3) Backside of this IC has a ground plate. Refer to 

How to

Replace the Flat Package IC

 (P.57)

(*4) Supplied IC is Flat Package Type.

Safety

Ref. 

No.

Part No.

Part Name & Description Remarks

 1

PNKM1125Z1 

       CABINET BODY

PS-HB

2

PQJJ1T039Y        JACK, MODULAR

  

3

K2ECYZ000001 

 

 

 

 

 JACK,  DC

   

4

L0AD02A00026 

 

 

 

 

 SPEAKER 

   

5

PQHG10729Z        RUBBER PARTS, SPEAKER

  

6

PQHR11313Z        GUIDE, SPEAKER

ABS-HB

7

PNKE1055Z1        CASE, CHARGE TERMINAL

PS-HB

8

PNJT1003Z         CHARGE TERMINAL

  

9

PNBC1002Z2        BUTTON, NAVIGATOR KEY

ABS-HB

10

PNHR1001Z         GUIDE, BUTTON

PS-HB

11

PNBC1001Z2        BUTTON, MESSAGE

AS-HB

12

PNJK1075Z         KEYBOARD SWITCH

  

13

PNYE1009Z         SPACER, ANTENNA

14

PNLA1030Z         ANTENNA 

  

15

PNKF1095Z1        CABINET COVER

PS-HB

16

PNHA1014Z         

RUBBER PARTS, FOOT
CUSHION 

  

17

PNHA1013Z         

RUBBER PARTS, FOOT
CUSHION 

  

Safety

Ref. 

No.

Part No.

Part Name & Description Remarks

 

PCB1

PNWP16521BXH MAIN P.C.BOARD ASS'Y

(RTL)

  

(ICs)

IC3

C0DBAGZ00026 IC                               

IC7

C1CB00002906 IC (BBIC(FLASH))

(*1)(*3)(*4)

  

IC401

PNWITG6521EH IC (EEPROM) (*1)

  

IC421

C3FBLY000048 IC

  

IC801

C1CB00001842 IC (*3)

  

(TRANSISTORS)

IC2

B1ZBZ0000065 TRANSISTOR(SI)                   

Q2

B1ABCE000009 TRANSISTOR(SI)                   

Q3

B1ACGP000007 TRANSISTOR(SI)                   

Q4

PQVTBF822T7 TRANSISTOR(SI)                   

Q5

2SD0874AS

TRANSISTOR(SI)                   

Q8

B1ADGE000004 TRANSISTOR(SI)                   

Q9

B1ADGE000004 TRANSISTOR(SI)                   

Q10

UNR92A6J0L

TRANSISTOR(SI)                   

Q24

UN9219J

TRANSISTOR(SI)                  S

Q25

UN9219J

TRANSISTOR(SI)                  S

Q421

2SC6054JSL

TRANSISTOR(SI)                   
(DIODES)

D3

B0EDER000009 DIODE(SI)                         

D10

MA8033

DIODE(SI)                        S

D21

PQVDRLZ20A

DIODE(SI)                        S

DA801

B0DDCD000001 DIODE(SI)                         

DA802

B0DDCD000001 DIODE(SI)                         

(COILS)

L1

PQLQXF330K

COIL                            S

L2

PQLQXF330K

COIL                            S

L3

G1C220M00037 COIL                            S

L801

G1C27NJ00010 COIL                             

L802

G1C3N0ZA0063 COIL                             

L803

G1C3N0ZA0063 COIL                             

(RESISTOR ARRAYS)

RA1

D1H810240004 RESISTOR ARRAY

 S

RA402

D1H410320002 RESISTOR ARRAY

  

RA501

D1H810240004 RESISTOR ARRAY

 S

RA80

D1H422120001 RESISTOR ARRAY

  

(VARISTOR)  

SA1

J0LF00000026 VARISTOR (SURGE

ABSORBER)  

  

(RESISTORS)

R3

PQ4R10XJ184 180k                            S

R4

PQ4R10XJ105 1M                              S

R5

PQ4R10XJ184 180k                            S

R6

PQ4R10XJ105 1M                              S

R7

ERJ3GEYJ565 5.6M                            S

R8

ERJ3GEYJ104 100k                            S

R9

ERJ3GEYJ565 5.6M                            S

Safety

Ref. 

No.

Part No.

Part Name & Description Remarks

Summary of Contents for KX-TG6521BXB





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands