65
KX-TGF340/KX-TGF342/KX-TGF343/KX-TGF344/KX-TGF345/KX-TGF372/KX-TGF373/KX-TGF374/KX-TGF375/KX-TG585/KX-TGFA30
12.5. Things to Do after Replacing IC or X'tal
If repairing or replacing IC and X'tal, it is necessary to download the required data such as Programming data or adjustment data,
etc. in memory.
The set doesn't operate if it is not executed.
12.5.1. How to download the data
12.5.1.1. Base Unit
First, operate the PC setting according to
Then download the appropriate data according to the following procedures.
Note:
(*1) XXX_YYY: revision number, ZZZ:Voice prompt, AA: Baud rate(9600/19200/57600/115200)
"XXX_YYY and
"ZZZ" vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in
(*2) Refer
When adjust the frequency the BT Unit.
Note:
: Enter key
Items
How to download/Required adjustment
BBIC(IC501)
Programming data is stored in memory.
1) Clock adjustment: Refer to
FLASH1 (IC601)
Voice prompt data is stored in memory.
(vary depending on country version)
1) Wait more than 15 seconds after connecting the JIG Cable.
2) Execute the command “VPDL2011 -AA ZZZ.bin” (*1).
(writing time: approx. 1 min (115200 bps).)
FLASH2 (IC502)
Program D/L
1) Update BBIC.
2) Detach the JIG cable, then disconnect the DC Power.
3) Connect the DC Power.
4) Connect the JIG cable again, and execute the command
"getchk", then confirm the checksum value is correct.
If the downloading failes, start again from step 1.
5) Execute the command "wreeprom 00 01 CC". Refer to
12.2.4. Commands
6) Default bath file: Execute the command "default.bat"
7) Country version batch file: Execute the command
"TGF34x_US_US_RevXXX_YYY.bat" (for KX-TGF340) or
"TGF37x_US_US_RevXXX_YYY.bat" (for KX-TGF370). (*1)
8) Confirm DECT ID written in the label pated plastic bag of
FLASH rom.
9) Write ID(PFPI): Write DECT ID in step 8.
=> Execute the command "writeid". Refer to
12.2.4.
10) Verify ID(PFPI): Execute the command "readid". Refer to
12.2.4.
11) Clock adjustment: Refer to
.(*2)
X'tal (X501)
System clock
Clock adjustment data is in EEPROM, adjust the data again
after replacing it.
1) Apply 5.5V between DCP ad DCM with DC power.
2) Input Command "sendchar sfr", then you can confirm the
current value.
3) Check X'tal Frequency.(10.368MHz ± 41Hz).
4) If the frequency is not 10.368MHz ±41Hz, adjust the
frequency of CLK executing the command "sendchar sfr xx xx
(where xx is the value)" so that the reading of the frequency
counter is 10.368MHz ±5Hz.
Item
Test command
Description
Input
Echo back
1
Power on
-
-
Wait 10seconds and connect JIG
2
Test mode
sendchar XBT 1
sendchar #X ts
OK
#XXTEST
Enter"XBT 1" and then "OK" is back
when it succeeds to enter test mode.
3
Confirm a default value
sendchar #X nc
#XXnc=0x1A
Confirm a default value before adjusting the
frequency.
4
Adjust the frequency
sendchar #X b3 39 19
sendchar nc,,
#XXTS ch=2441 pwr=19
#XXnc=0x,,
Adjust the frequency to "2441MHz ± 10kHz" by
changing the value of,
Test Point: ANT_BT, refer to
