Panasonic KX-TCD816UAS, Service Manual

Page: 27 / 101

Items Check
Point
Procedure Check or
Replace Parts
( F )* BBIC Clock Adjustment CLK 1. Input Command “rdeeprom 00 01 01”, then you can confirm the current value.
2. Adjust the frequency of CLK executing the command “setfreq xx (where xx is
the value)” so that the reading ofthe frequency counter is 10.368000MHz ±
10Hz.
IC2, R124,
R125, C153,
X1, C42, C43,
R40
( G )* Hookswitch Check with
DC Characteristics
- 1. Connect CN1 (Telephone Socket) to Tel-simulator which is connected with
600
Ω
.
2. Set line voltage to 48V and line current to 40mA at off-hook condition of
normal telephone.
3. Execute the command “hookoff”
4. Confirm that the line current is 40mA ± 5mA.
5. Execute the command “hookon”.
6. Confirm that the line current is less than + 0.8mA.
CN1, L6, L7,
Q4, R23, R25,
Q5, R26, R28,
IC8, D3
( H )* DTMF Generator Check - 1. Connect CN1 (Telephone Socket) to DTMF tester. (Road=600
Ω
)
2. Link Handset and push dial key.
3. Confirm DTMF character.
4. Confirm that the high Group is -3dBm ± 2dBm.
5. Confirm that the low Group is -6dBm ± 2dBm.
IC8, R39, C41,
R49, C46, C47,
R42, R43, R44,
R45, R46, R47,
R48, C108,
C109, C40,
C36, Q8, D4
( I )* Transmitted Power
Confirmation
- Remove the Antenna before starting step from 1 to 7.
1. Configure the DECT tester (CMD60) as follows;
<Setting>
• • • •
Short A_1-GND and A_2-GND.
• • • •
Test mode: FP
•
• •
•
Traffic Carrier: 5
• • • •
Traffic Slot: 4
•
• •
•
Mode: Loopback
• • • •
PMID: 00000
•
• •
•
RF LEVEL = -70dBm.
2. Execute the command “testmode”.
3. Execute the command “sendchar dmv 2 2”.
4. Check that “Signalling Status” has been set to “Locked”, then press “ACCEPT
RFPI”.
5. Initiate connection from Dect tester (“set up connect”)
6. Execute the command “ANT1”.
7. Confirm that the NTP value at ANT is 20dBm ~ 25dBm.
IC2, IC8, R124,
R125, C153,
C140, C141,
DA1, C142,
C143, C144, L3,
L4, R118, R119,
C135, R115,
R116, Q6,
C145, C147,
C149, C151,
C157, R123,
C158, C159,
C160, C161,
C162, C163,
C164, C136,
R117, R127,
C156, C154,
C155
( J ) Modulation Check and
Adjustment
- Follow steps 1 to 6 of (I) above.
7.Confirm that the B-Field Modulation is -350 ~ -400/+320 ~ +370kHz/div
using data type Fig31.
8.Adjust the B-Field Modulation ifrequired. (Execute the command “readmod”
and “wrtmod xx”, where xx is the value.)
IC2, IC8, R124,
R125, C153,
C140, C141,
DA1, C142,
C143, C144, L3,
L4, R118, R119,
C135, R115,
R116, Q6,
C145, C147,
C149, C151,
C157, R123,
C158, C159,
C160, C161,
C162, C163,
C164, C136,
R117, R127,
C156, C154,
C155
27
KX-TCD816UAS / KX-TCD816U AT / KX-TCA181UAS / KX-TCA181UAT