manualshive.com logo in svg

Panasonic KX-TCD200E, Operating Instructions Manual

Share
Download
Panasonic KX-TCD200E Operating Instructions Manual Download Page 38

Useful Information

38

Helpline Tel. No.: U.K. 08700 100 076  R.O.I. 01289 8333

Troubleshooting

If you still have difficulties after following the instructions in this section, disconnect the AC 
adaptor and turn off the handset, then reconnect the AC adaptor and turn on the handset.

Initial settings

Problem

Cause & solution

w

 is flashing.

L

The handset is not registered to the base unit. 
Register it (page 31).

L

The handset is too far from the base unit. Move 
closer.

L

The AC adaptor is not connected. Check the 
connections.

The handset display is blank.

L

The handset is not turned on. Turn the power on 
(page 10).

The handset will not turn on.

L

Make sure that the batteries are installed correctly 
(page 9).

L

Fully charge the batteries (page 9).

L

Clean the charge contact and charge again (page 
9).

TCD200E(e-e).book  Page 38  Wednesday, February 9, 2005  2:58 PM

Summary of Contents for KX-TCD200E













































Reviews:

No comments

Brands by name

Popular brands

Load more brands