Panasonic KX-PRX120W Service Manual Download Page 20

Page: 20 / 89

KX-PRX120W/KX-PRXA10W

8.4.

How to Clear User Setting

Units are reset to the Factory settings by this operation (Erase stored Phone numbers, Caller list and etc.)

Note:

• Some menus are not reset. Refer to

Operating Instructions

(P.16).

• The reset menus differ depending on the following operations.
•

This operation should not be performed for a usual repair.

8.4.1.

Resetting both base unit and handset

Both the base unit and the registered handset which you did the following steps

are reset. Other registered handsets

will not be reset.

Note:

(*1) Refer to

Registering a Handset to a Base Unit

in the Operating Instructions.

Connect the AC adaptor to the base unit and install the charged batteries into the handset.

Confirm the handset is registered to the base unit ( ).

If the handset is not registered to the base unit ( ), register it. (*1)

Press "*#72627664*#" to enter Factory Mode.

Factory Reset --> Factory reset1

Keep pressing Power Button at language select screen and select shutdown.

Disconnect the AC adaptor of Base unit.

Keep pressing the power key and home key at the same time until "Android system recovery" is displayed.

(about 10 seconds)

Move the focus to "wipe data/factory reset" by Volume button and push the power key.

Move the focus to "Yes -- delete all user data" by Volume button and push the power key

Remove the battery after the "Data wipe complete."

Handset

Base unit

Summary of Contents for KX-PRX120W


























































































Search results

Summary of Contents for KX-PRX120W

Reviews:

Related manuals for KX-PRX120W

Brands by name

Popular brands

Panasonic KX-PRX120W, Service Manual

Search results

Summary of Contents for KX-PRX120W

Reviews:

Related manuals for KX-PRX120W

Brands by name

Popular brands