![background image](http://html1.mh-extra.com/html/panasonic/kx-ns500/kx-ns500_features-manual_3554256173.webp)
2.11.6 Flash/Recall/Terminate
Description
The FLASH/RECALL button (Flash/Recall mode or Terminate mode) or Terminate button (Terminate mode)
is used when a PT user disconnects the current call and originates another call without hanging up first. It
performs the same function as going on-hook and then going off-hook.
[Explanation of Each Mode]
Flash/Recall Mode:
Disconnects the line. The extension user hears the dial tone from the line used last. For
example, if a trunk call is disconnected, the extension user will hear a new dial tone from the telephone
company.
Terminate Mode:
Disconnects the line. The extension user hears the dial tone determined by the Line
Preference—Outgoing setting. (
®
2.5.5.2 Line Preference—Outgoing)
Conditions
•
FLASH/RECALL Button Mode
One of the following modes can be selected for each extension through system programming:
–
Flash/Recall mode
–
Terminate mode
–
External Feature Access (EFA) mode. (
®
2.11.7 External Feature Access (EFA))
•
Terminate Button
A flexible button can be customised as the Terminate button.
•
Disconnect Time (Only for Flash/Recall Mode)
The amount of time between successive accesses to the same trunk is programmable for each trunk port.
•
This feature outputs an SMDR call record (
®
2.22.1.1 Station Message Detail Recording (SMDR)), restarts
the call timer, inserts the automatic pause, and checks the TRS/Barring level (
®
(TRS)/Call Barring (Barring)) again.
•
The Terminate feature will be performed when pressing the FLASH/RECALL button regardless of the mode
that the FLASH/RECALL button has been set to, in the following situations:
–
When a call is made using ARS. (
®
2.8.1 Automatic Route Selection (ARS))
–
When a trunk call is made with the INTERCOM button.
–
When a trunk call is made with an ICD group button.
•
For general SIP phones, the function of a FLASH button differs depending on the phone, and its
functionality does not depend on the setting specified in the PBX.
PC Programming Manual References
9.24 PBX Configuration—[1-1] Configuration—Slot—Port Property - LCO Port—
12.1.1 PBX Configuration—[4-1-1] Extension—Wired Extension—Extension Settings—Option 7—
12.2.1 PBX Configuration—[4-2-1] Extension—Portable Station—Extension Settings—Option 7—
PT Programming Manual References
Feature Guide
173
2.11.6 Flash/Recall/Terminate
Summary of Contents for KX-NS500
