9.17 PBX Configuration—[1-1]
Configuration—Slot—V-IPCS—Card Property
The properties of the V-IPCS card can be specified.
Signalling (PTAP) UDP Port No. (Server)
Specifies the UDP port used by the V-IPCS card to transmit and receive PTAP (Panasonic Telephony
Administration Protocol) data. This must be changed if another network application is using the same port.
To change the value displayed here, click
Common Settings
and set the desired value.
Value Range
1024–65535
Signalling (MGCP) UDP Port No. (Server)
Specifies the UDP port used by the V-IPCS card to transmit and receive MGCP (Media Gateway Control
Protocol) data. This must be changed if another network application is using the same port.
To change the value displayed here, click
Common Settings
and set the desired value.
Value Range
1024–65535
Signalling (MGCP) UDP Port No. (IP-CS)
Indicates the UDP port used to transmit and receive MGCP (Media Gateway Control Protocol) data on the
IP-CS side (reference only).
Value Range
2427
Voice (RTP) UDP Port No. (IP-CS)
Specifies the UDP port used to transmit and receive RTP (Real-time Transfer Protocol) data on the IP-CS side.
This must be changed if another network application is using the same port.
For voice communications, an IP-CS uses 128 contiguous UDP ports, starting from the port number specified
here.
To change the value displayed here, click
Common Settings
and set the desired value.
Value Range
1024–65024
Keep Alive Time-Out
Specifies the length of time that the PBX will continue to consider an IP-CS to be active even if it receives no
transmissions from that IP-CS. The PBX constantly confirms the status of IP-CSs. If no communications are
received from an IP-CS for the duration specified here, the PBX considers the IP-CS to be unreachable, and
sets the port status to
Fault
.
During operation, set between 10 s and 60 s. Settings over 60 s, and
Disable
, are used for debugging purposes,
and IP-CSs cannot be guaranteed to function normally in these circumstances. Do not use debugging settings
unless instructed to do so.
278
PC Programming Manual
9.17 PBX Configuration—[1-1] Configuration—Slot—V-IPCS—Card Property
Summary of Contents for KX-NS300CN
