background image

 

SIP Trunk 

– Port Property continued 

[Account] Tab 

1. User name:   

Enter the 

Username as supplied by I-Net Connect. 

(Note this is username without @ipbx.inetplc.org) 

For example: Username = 

12345670

 

Enter: 

12345670

 

2. Authentication ID:   Enter the 

Authentication ID as supplied by I-Net Connect. 

(Note this is Authentication ID without @ipbx.inetplc.org) 

For example: Authentication ID = 

12345670

 

Enter: 

12345670

 

3. Authentication   

Enter the 

password as supplied by I-Net Connect 

Password:   

For example: password = 

passwordABCD

 

Enter: 

passwordABCD

 

 

 

   

 

 

 

 

[Register] Tab 

1. Register Ability:   

 

 

Leave enabled

 

2. Register Interval:   

 

 

Enter: 

120

 

3. Un-Register Ability: 

 

 

Leave enabled

 

4. Registrar Server 

– Name:   

 

Not required 

5. Registrar Server 

– IP Address: 

 

Not required 

6. Registrar Server port number: 

 

Leave at 5060 

6. Registrar Server port number: 

 

Leave at 5060 

Click 

[OK]

 to apply the changes. 

Select 

[INS]

 on the 

[V-SIPGW16] 

card to bring the SIP trunk ports into service. 

Summary of Contents for KX-NS Series
















Reviews: