94
KX-FLC418RU
11.1.3. Service Function Table
Code
Function
Set Value
Effective
Range
Default
Remarks
501
Pause time set
1:3S (Short)
2:5S (Long)
1, 2
1
----------
511
Vox sense
1:HIGH /
2:LOW
1, 2
1
When the TAM (or EXT TAM) does not stop
recording the ICM because noise is detected on
the telephone line, change this setting to "LOW".
514
Bell signal detect time
X 100msec
1~9
5
----------
520
CED frequency select
1: 2100 Hz
2:1100 Hz
1, 2
1
See Symptom/Countermeasure Table for long dis-
tance and international calls in
(
.
521
International mode select
1:ON 2:OFF
1, 2
1
See Symptom/Countermeasure Table for long dis-
tance and international calls in
(
.
522
Auto standby select
1:ON 2:OFF
1, 2
1
----------
523
Receive equalizer select
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4
1
Set RX equalizer to automatic mode.
524
Transmission equalizer select
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4
1
529
Call Service Clear
544
Selecting the document feed position
0~4mm
0~4
2
When the ADF function is incorrect, adjust the
feed position.
550
Memory clear
See
.
551
ROM check
See
.
553
Monitor on FAX communication select
1:OFF
2:PHASE B
3:ALL
1~3
1
Sets whether to monitor the line signal with the
unit's speaker during FAX communication or not.
554
Modem test
See
.
555
Scan check
See
.
556
Motor test
0
See
.
557
LED test
See
.
558
LCD test
See
.
561
KEY test
See
.
567
T0 timer
X second
001~255
028
Sets a higher value when the response from the
other party needs more time during automatic FAX
transmission.
570
BREAK % select
1:61% 2:67%
1, 2
1
Sets the % break of pulse dialing according PBX.
571
ITS auto redial time set
X number of
times
00~99
03
Selects the number of times that ITS is redialed
(not including the first dial).
572
ITS auto redial line disconnection time
set
X second
001~999
065
Sets the interval of ITS redialing.
573
Remote turn-on ring number set
X number of
rings
0~99
00
Sets the number of rings before the unit starts to
receive a document in the TEL mode.
574
DIAL TONE detection ON/OFF section 1:ON / 2:OFF
1, 2
2
Sets whether to dial the Automatic dial number
before detecting dial tone or after detecting dial-
tone.
590
FAX auto redial time set
X number of
times
00~99
03
Selects the number of redial times during FAX
communication (not including the first dial).
591
FAX auto redial time disconnection time
set
X second
001~999
065
Sets the FAX redial interval during FAX communi-
cation.
592
CNG transmit select
1:OFF
2:ALL
3:AUTO
1~3
2
Lets you select the CNG output during FAX trans-
mission. ALL: CNG is output at phase A. AUTO:
CNG id output only when automatic dialing is per-
formed. OFF: CNG id not output at phase A. Refer
to
)
.
593
Time between CED and 300bps
1:75 msec
2:500 msec
3:1 sec
1~3
1
See
Symptom/Countermeasure Table
for long
distance and international calls in
(
. Refer to
(
and
(
.
594
Overseas DIS detection select
1:detects at the
1st time
2:detects at the
2st time
1, 2
1
See
Symptom/Countermeasure Table
for long
distance and international calls in
(
. Refer to
(
and
)
.
Summary of Contents for KX-FLC418RU
