KV-SSM100/KV-SS1100 NETWORK SCANNER ADAPTER
QUICK SETUP GUIDE
This guide is intended for the network administrator/solutions engineer responsible for setting up the KV-SSM100/
KV-SS1100. It contains key steps to connect the adapter to a Panasonic Scanner, and then perform basic Scan to Folder
operations. For instructions on how to set up Scan to Email, Scan to Fax, Scan to Bluetooth and Scan to Printer, please
refer to the KV-SSM100/KV-SS1100 Network Scanner Adapter Administrator’s Guide.
STEP 1:
PERFORM INITIAL CONFIGURATION
1.
Press [
Power
] button to turn adapter
On
.
2.
Press [
Configure Device Now
].
3.
Enter
Admin Password
of your choice.
4.
Re-enter to
Confirm
password.
5.
Press [
Enter
] to save password.
Note:
n
Password must be at least six (6) characters.
n
Password is case sensitive.
n
Password can be changed after configuration.
6.
Continue with
Network Settings
…
Network Settings
Select type of network connection:
1.
Wired Settings (default)
– Adapter will obtain IP address from
DHCP server, and auto-populate remaining fields. Deselect
checkbox to manually input IP address settings. Press [
Next
], and
continue with
Shared Folder Configuration
(below).
Note:
Ethernet cable must be attached to adapter from network
switch in order for IP address to be obtained.
2.
Wireless Settings:
Select [
Wireless
]. Connect to WiFi network by
pressing [
Wireless Discovery
]. SSID field should be automatically
populated. If not, manually input SSID. When WiFi networks
display, select/highlight network, and then press [
Select
]. Enter
Security Key
, and press [
Next
], and continue with
Shared Folder
Configuration
…
Shared Folder Configuration
Once Network Settings are complete, the
Share Management
screen
appears, where you can use
Network Discovery
to search for public
Windows shares within the network.
Note:
To manually set up UNC or
FTP folder paths, use
Manual Setup
instructions (see page 2).
Network Discovery
1.
On
Share Management
screen, press [
Add
].
2.
On
Add Share
screen, press [
Search
].
Important:
If no network shares are discovered, i.e., Search
screen is blank, manual setup is required, as the computer is likely
password protected, in which case you must enter the folder path
and login credentials manually. (See next page.)
3.
On
Network Discovery
screen, select
workgroup/domain
and
PC
where shared folders are located.
4.
Press [
Select Share
].
5.
Enter
Friendly Name
(required).
Note:
You cannot add two shares with the same Friendly Name.
BEFORE YOU BEGIN
Confirm the following:
Power cable is connected to adapter.
1.
Connect AC adapter to DC-in jack of adapter.
2.
Connect AC adapter to power cord.
3.
Plug power cord into electrical outlet.
Panasonic scanner is installed.
1.
Connect USB cable from scanner to adapter.
Connection method is known:
Wired:
Cable is connected from adapter’s Ethernet port
to network switch/router.
Wireless:
Ensure that wireless router is working
correctly and that there is
no
network (Ethernet) cable
attached to the adapter. Have the following information
available:
n
SSID
(e.g., NETGEAR62)
n
Security Mode
(Open, WEP, WPA Personal, WPA2
Personal).
Note:
WPA Enterprise and WPA2 Enterprise
Wi-Fi networks are not supported.
Network is configured for folder sharing.
n
Ensure that Network File and Folder Sharing settings
and permissions are established.
n
To enter FTP server addresses or UNC paths, to
manually locate shared folders, have path information
available.
n
If access to shared folders requires authentication (or
folder is on an FTP server), you must manually locate
the folders. Know your login credentials.
